4KSM50PWH0 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from GLEN ALLEN, VA
- Parts Used:
- WP3182857
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring latch was broken
changed the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from LEXINGTON, SC
- Parts Used:
- W11312468
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Splash from K45 KitchenAid Mixer Bowl
The shield works sufficiently. Note that the shield is not a continuous circle as shown in the picture. This actually can be an asset because it can be installed or disassembled without stopping the mixer of having to lift the head while running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from OSSINEKE, MI
- Parts Used:
- WPW10325124
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Control stuck in high gear.
With the mixer being over 30 years old we believed it has going to have to be replaced. However, my husband jumped on uTube and looked at reviews for the problem. Motor was only running on high speed. Reviews said to replace the phase control board. Repair was very quick by just taking off the cover. Removing the old board and connecting the new. Mixer is working awesome once again. In such a disposable society it is great to be able to fix vs trash. Happy Baker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabrina from BUNKIE, LA
- Parts Used:
- WPW10380496
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt brushes
The brushes are located on each side of the tilt head of the mixer. I used a screwdriver to remove the screws, removed the brushes & replaced with the new ones. Runs great again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from JACKSONVILLE, FL
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Mixer went to high speed immediately on starting
Simple fix actually. UNPLUG mixer and remove the one screw on top that holds on the back. The Phase control board sits under and behind the paper insulator and "switch" assy. Remove the 4 wires with a pair of needle nose pliers, the one screw holding it to the back of the mixer and install the new one in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ely from Monsey, NY
- Parts Used:
- WP3182857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bowl shaking during use
line up the screw holes and screw it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GALO from DECATUR, GA
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer operarates at high speed only.
Removed old one and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from NEW YORK, NY
- Parts Used:
- WP3182857
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring latch snapped off making bowl unstable and unless hand stabilized wobbled too much to use.
SO SIMPLE!!!!! Using a regular screwdriver, remove the remains of the Spring Latch. Place new one over holes and screw new one in place using the currently used screws. May wash off screws first if caked with gunk. OMG!!! TOOOO easy and saved me from throwing out a very terrific 40 year old PRO LINE KITCHEN AID MIXER!! To replace it would have been hundreds of dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from PALISADE, CO
- Parts Used:
- WPW10112253, W11192794, WP4162324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Decorative plug at top of mixer fell into the bowl and jammed the mixer stripping gears
Watch U Tube video. Take care to keep track of disassembly. Hard part was to have 4 types of screw drivers to fit the different screw heads. Be sure to clean broken gear clogs out of the grease. Parts select lady was a great help. Download Parts select diagram for extra help. Time and patience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachael from SEATTLE, WA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Worm gear was stripped and needed to be replaced
I am not handy, but was able to follow this YouTube video and do this repair easily and successfully: https://www.youtube.com/watch?v=1QsgPIL9FpA
I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!
I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!
Was this instruction helpful to you?
Thank you for voting!
Replaced a feb 1976 2 prong cord
Got a harvest gold mixer from g maw and thought a project would be nice we have several of these mixers in the family i knew a 2 prong cord was not safe so i took apart the mixer and wanted to regrease it just give a lookie to see what i needed and then i decided after watching video on y tube to convert to a solid state.
Parts select as a whole has been very understanding as a whole and i will continue to get parts thru them they are genuine parts which is something i had to have i have 90% of my parts for a full overhaul we just cannot get the parts delivered fedex and usps i specify the address and they deliver 2 blocks east of the house thanks for honest neighbors usps was late as usual like i said parts select is outstanding at placing the order and appliances can be fixed super simple with the right tools the concern is with the fedex and usps now they are shorthanded but lets be real but when you deliver a package just triple check it is the right house !
Parts select as a whole has been very understanding as a whole and i will continue to get parts thru them they are genuine parts which is something i had to have i have 90% of my parts for a full overhaul we just cannot get the parts delivered fedex and usps i specify the address and they deliver 2 blocks east of the house thanks for honest neighbors usps was late as usual like i said parts select is outstanding at placing the order and appliances can be fixed super simple with the right tools the concern is with the fedex and usps now they are shorthanded but lets be real but when you deliver a package just triple check it is the right house !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CEDAR CITY, UT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic worm gear gave way (as designed) when the grain mill over-worked it.
I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Kathleen, GA
- Parts Used:
- WPW10380496, WP4162324, WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Worms Gear broken teeth from the gear.
Followed web site's videos. One step left out of video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from HAMPTON, NH
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My stand mixer stopped mixing!
I watched a YouTube video all the way through, then watched each segment and followed along with the video. It was messier than the professional repair guy, but it worked out fine. This is not a difficult repair when you can watch a video and follow along. It saved me about $130.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from ELY, MN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No rotation on mixer
You tube has great instructions! I would suggest when you buy a part to let customer know that they need a food grade gear grease ordered to complete the reinstall of all gears and body parts!
Was this instruction helpful to you?
Thank you for voting!