KG25H0XBM5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from SAINT LOUIS, MO
- Parts Used:
- WP9708649
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
needed to replace rubber foot on mixer
The insertion part of the foot was tapered to fit in the hole in the mixer. Simple pressure was not the answer. So I used a small key, placed it on the bottom of the foot, after applying a little vegetable oil on the foot, and tapped it into place. Worked well.Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hamburg, MN
- Parts Used:
- WPW10170081, WPW10170080, 8212396, WP9709511, WP9709231, W11086780, WP9703445
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gears and bearing failure
inspected and replaced worn components
Was this instruction helpful to you?
Thank you for voting!
Last repairperson broke the top cover of the gearcase ; still need this part .
Easy ; remove belt ( 1 screw ) remove cover , and there is the complete drive . I still need the top plastic cover which is cracked and broken where the bolts go through . Please quote this part .Conradt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Mentone, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.
Was this instruction helpful to you?
Thank you for voting!
mixer was very noisy when running and made a horrible grinding sound
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from North Olmsted, OH
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Part broken
Easy thanks to your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from SOUTH ELGIN, IL
- Parts Used:
- W11192795
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken gears
Fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madeleine from NEW YORK, NY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Jamestown, ND
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gear teeth worn off worm gear
replace worm gear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCISCO from SAN BENITO, TX
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
REPLACE SPEED CONTROL SWITCH
REPLACE SPPED CONTROL SWITCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Harrodsburg, KY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Speed switch bad and Initially thought new part was wrong!
At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.
Was this instruction helpful to you?
Thank you for voting!
Bad control switch, striped worm follower gear.
Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from LARGO, FL
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PEORIA, AZ
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Stripped Gear Mixer would not mix
I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.
Was this instruction helpful to you?
Thank you for voting!