KP26M1FQTG5 KitchenAid Mixer - Instructions

removed the cover as stated in the e-mail and followed their recommendations on how to do the repair, the hardest part was removing the retainer clip, job went smoothly. thanks

Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.

The KitchenAid is "old school" in that it is held together with simple (but very stout) bolts and screws. I removed about 10 such fasteners, slipped off the gear retainer, and pulled it out. On Sunday, a very nice customer service rep helped me order the right part, but I did the rest on line in a matter of seconds. It shipped on Monday and arrived on Wednesday. Took about 10 minutes to put everything back. I REALLY WISH everything was this easy in 2012!!!

I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie

Easy repair that replaced the variable speed switch. The broken switch only ran at high speed. To replace the mixer would cost at least $500. The new switch was $45 and was an easy install. I marked the four electrical leads with a Sharpie and loosened the two screws holding the switch. The repair was super easy. It was like heling an old friend recover from an illness.

Open the case, removed gear cover, removed planetary drive shaft and gear, replaced with new planetary and reassemble.

removed top casing, removed old switch and sensor,and replaced with new ones. It was just a matter of a half dozen screws and unpluging 4 or 5 wires and then reversing the process. Couldn't be easier. thank you

took off the strap band around mixer, took off the cover (4 screws, took off gear cover (4 screws) took off the retaining ring(used pliers and screwdriver) took off upper gear, took out retaining pin, took off lower gear (becareful to grab the planetary assembly as it will fall out after you take out the retaining pin) cleaned out all of the gear grease (the teeth that were missing were in it. replaced the planetary assembly, lower gear and retaining pin. replaced the upper gear, replaced the retaining ring (used screwdriver and hammer. you have to spread the ring with end of screw driver so it will fit on the shaft then tap lightly with screwdriver and hammer to get it down to the keyway for the ring.) replaced the gear grease with NEW grease, reaplaced the gear cover, replaced the mixer cover, replaced the strap band and plugged it in to test it. IT was quieter than before and works great. i spent less than $30 to repair my 10 year old, out of warranty, Kitchen Aid Mixer. much better than the $32.00 to ship it to factory repair shop and get an estimate to repair. I needed it to make a cake for my nephews wedding. I had my parts in 2 DAYS!!! it was a great experience over all.

The appliances belong to my neighbor who had no papers/manuals so I was on my own to figure out how to even get the machine apart and to find the correct nomenclature for the parts I needed. The PartSelect diagrams on the web site told me everything I needed to know. The key to the dis-assembly was the band around the center of the machine. After I discovered that, the band came off easily followed by splitting of the casing. One the first machine it appeared that the circuit board/switch assembly was in bad shape looking like it had been over heated at one time. As a test, I took the electric component out of the machine that would run and put it on the dead mixer. Beauty, it worked. OK so much for the easy one. On the machine that would only turn part way, I split the transmission housing by removing four small bolts and found that the worm gear was partially stripped. So, I ordered a new gear, switch assembly and transmission gasket since the old one was torn during my dis-assembly process. I don't have any snap ring pliers, so the snap ring(retaining ring) was taken off using a large screw driver and a a pair of slip joint pliers. Worked well, but I was afraid that the old retaining ring may have been damaged, so I ordered a new one. Good idea, since I broke the old one trying to put it back on. When all of the parts were installed, I filled the voids with heavy grease and put it all back together. Both mixers now work perfectly which saved the owners several hundred dollars. They had planned on replacing them both for use at their restaurant. I am now a fan of PartSelect because of the ease at which I, a novice had been able to find and get the correct parts, and the speed at which they arrived. I am also very impressed with the Kitchen Aid mixers because it appears the they are very well made, and are easily repaired if they do break. I was surprised to find a small appliance that is repairable. Many are now just throw away quality. I am a hero to my neighbors (they don't know how easy this was) and will keep the refrigerator magnet that was included with my parts order, for future repairs.

removed the cover, separated the gear casing, cleaned the gears, replaced the thrust bearing kit and worm gear, greased all and reassembled. Wish I would have known to order the grease, it would have saved a couple bucks in shipping.

Removed the cover. Removed the gear assembly cover.. Extracted the C clip with a tool. Removed the bevel gear. Pushed out the dowel pin. Used rubber mallet to push the shaft off the worm gear. Replaced the washer and the worm gear. Used a 1/2" diameter PVC, 3" long over the shaft and on the gear to push back the shaft through the gear with rubber mallet. Pushed back the dowel pin. Reinstalled the C clip. Replaced broken hub bevel gear. Added more grease. Placed the gear cover with 4 screws just tight enough to hold the cover but still allows movement. Turned the mixer to the lowest speed. Allow the cover to self adjust so that the gears have the smoothest sound. Tightened the screws while while maintaining the smooth sound. Turned off the power. Replaced the cover.

Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again

replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.

I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.

ordered the part and put in in with the help from the instant repairman