KF26M22CA5 KitchenAid Mixer - Instructions

Remove screw and nut from back of mixer head to release the silver name band. Remove the exposed four cross head screws, (two each side), and lift off the motor and gear cover. Wipe excess grease from gear wheels to expose the retaining ring clip at top of vertical gear shaft. Using small nose circlip pliers, remove retaining ring and bevel gear wheel to expose shaft pin and worm gear. Support the shaft from below and remove pin. Lift off worn worm gear wheel allowing shaft to drop down. The horizontal worm gear shaft can now be lifted out taking care to keep assembled. Carefully clean old grease from all gears and from the gear housing, (note that broken pieces of the old worm gear are in the old grease. Repack housing with fresh high performance grease recommended for worm drives. Cover new and reuseable gears with grease. Reverse the process to reassemble the unit.

We are a pretty handy bunch here. However, the diagrams provided with the part numbers did assist in the disassembly. It went smooth and easy.

Removed one screw to remove deco band around mixer body. Removed four screws under band to remove mixer top. Removed two screws holding switch. Removed wires one at a time putting them in the same position on the new switch. Re-attached switch, mixer top, and deco band. Works perfectly.

Removing the cover of the mixers "guts", it was immediate evident the a major gear had lost a few of its "teeth". Parts Select clearly offered the required part of this $300 mixer for a favorable price. I was fully impressed that it arrived within 4 days or my ordering the part. I simply exchanged the damaged gear and restored the mixer to service and I'm fully impressed with the Parts Select Company for their swift response to my needs.

remove the cover,take out four screw from gear box,remove the gear box,clean all gears,then you see damage gear,replace it ,install new grease.

___ Remove silver decorative band/1 screw ___ Remove top of mixer/4 screws ___ Remove circuit board/2 screws ___ remove 5 wires from ckt. bd. (be sure where they go) ___ Install new ckt. bd. with proper electircal connections ___ test mixer/OK ___ Reassemble & retest/OK

Following Replacement Part Youtube instructions, I disassembled the mixer and found what caused the sounds and prevented the mixer from operating. The worm follower gear had been ground down by the worm gear. I found that the shaft from the planetary gear had not been adequately greased and siezed preventing the worm follower gear from turning. The worm gear is obviously made of harder material and thus, was able to wear away the follower. I appreciate the your help which saved having to replace a perfectly good/expensive mixer. Thanks.

took mixer apart down to removal of gear case cover.upon removal of this cover found the bevel gear and hub bevel gear chewed up .removed them both then replaced them both.and also had to solve a clearence problem between the 2 gears they were too loosely meshing. so had to push the hub retainer closer to take up the meshing slack.not sure my repair will hold but i have another set of gears and another solution that will surely fix it.

First and foremost, I am not mechanical at all. I typically refer to parts as thing-a-ma-jigs, and whatca-ma-call-its. When it froze up and started to make a loud grinding noise, I guessed it was a gear problem. I decided to try to take it apart, What did I have to lose? If I couldn't figure it out, I would be down a mixer. I was already down one as it was. It was very easy to take apart and I could immediately see what gears needed to be replaced. Parts Select made it very easy to see what parts I needed. And delivery was lightning fast; the next day after it shipped! I found a PDF on line on how to dis-assemble and re-assemble the mixer. I got it together and it mixed for a few minutes and froze again. I took it apart and realized that I didn't have the whatcha-ma-call-it (worm gear) seated properly. Fixed it and put it back together and put it to the test. Working just fine now! Thank you Parts Select for making this very easy!

Removed shroud and gear case top. No snap-ring pliers, so I used two small vice grips, one on each lobe, and spread and "worried" the ring up the shaft. Changed out all ghe grease in case of metal chips. Put it back tegether. Works fine.

This is a 6 Qt. made by Kitchen Aid Stand Up mixer 575. watts with 6 qt. bowl. A powerful machine. But not geared to crush Almonds. After about 2 quarts of Almond crushing to make Almond butter I heard the machine thumbing inside and turned it off immediately. Mind you, I am a 60 year old man with Maintenance Mechanic, and Machinist skills. If you listen to my instructions which aren't that hard you can do this. REMOVE THE POWER CHORD BEFORE CONTINUING. First you have to find the screws that hold the top half of the machine together. They are under the silver Kitchen Aid Stainless Steel 5/8th Band that runs around the middle of the machine. On the back of the machine is a small machine screw that when taken out removes the band. Remove the band carefully as not to bend it because it has to go back on looking pretty. Comes off easy. You will then see 4 longer 3/4 inch screws around the middle of the machine head. When you remove these screws the top half of the machine head will lift up. The top half of the machine head lifts off very easy. Throw all your screws into the top so you don't mis place them. You will see a Motor some gears on the side and a shaft that comes from the motor going into a Cast Aluminum Casing with another 4 screws 3/4 exactly the same size as the ones you took from around the top mixer casing. This is easy cause you don't have allot of different size screws only the one small one that screws on the back of the band. After these four screws are removed, again lift up the top half of the casing but this time it will be full with gear grease. Put the casing aside and using paper towels wife a little of the gear grease off the top gear. In order to turn the gear you must use the side drive gear or look around the gear you will notice in some of the gear slots will be shinny and worn. This is the Bevel Gear. There is a C locking shaft cliff that keeps the gear locked in. You must have a multiple C clip remover pliers that has different size C clips for the holes in the clip must be spread apart in order to remove the clip all the way up the shaft. NOTE:; DO NOT USE A PLYERS TO TRY AND PRY THIS CLIP OFF IT IS STRANG AND YOU MAY MAR THE STAINLESS STEEL GEAR SHAFT. You must use the gear C clip remover, I found one moderately prized for 25 dollars at the Home Depot or any large chain hard ware stores will have it. After the C clip is removed, slide the gear evenly up. If it's stuck that's only because of grease unless you mar the shaft by not listening to me. I also replace the Top Hum Bevel gear which is in the top half of the hub. Parts select has a Diagram that shows you the parts and where they are. When putting on the Bevel Gear over the shaft be sure to lower it evenly and guide it onto the worm gear. There is a small pin that sticks out in the middle of the gear make sure this lines up when setting the gear into the worm gear. The Top Bevel Gear, falls right out and you can use your figures to pull this one out and put the new one in. If you replace the Bevel gear my experience as a mechanics is to always replaces the adjacent gear as well, both will be worn. attach the C cliff the same what as taking it off except opposite. Pull the tow clip holes apart and slide it down to the shaft groove for the clip. Put everything back the way you took it off. One NOTE;.. DO NOT DO TOUGHT THE SIDE DRIVE GEAR IT IS SET IN WITH BRASE LOCKING SHIMS AND HAVE TO BE SET A CERTAIN WAY TO CLOSE. When closing make sure the Top Hub is in line with these brace shims. After screwing the hub back down do not over tighten, just snug it tight. Be sure to buy axle gear grade and replace any grease removed, this chamber must be loaded with grease. There is never too much only too little as you will wear the gears down without the proper amount. DO NOT TOUCH ANY THING THAT DOES NEED TO BE TOUCHED LIKE THE MOTOR OR DRIVE SHAFTS OR SIDE MAIN GEAR…

Ordered new worm gear and received in a few days. I cleaned out old grease from the gear housing, replaced the worm gear and packed with new grease. Machine runs well now. Easy repair.

Noticed worm gear was worn out, ordered the parts, it came very next day. On YouTube instructions were very easy to follow. Important point to remember,I washed the parts in water with chlorine in it. Retaking ring was tough to take out, as I did not have parrot beak plier, could not find it at Home Depot or Lows. Putting the retaining ring I used circular nut driver, to press it on the shaft to slide down by hammering it. While assembling follow the instruction step by step from the you tube. Machine works smoothly. Performing well. Thanks to part select, excellent web page, efficient delivery. I would recommend them to all.

Worm gear strips usually after the lower gear housing breaks. Tore down cleaned grease and shrapnel out, replace stripped worm gear and lower housing. It's convenient that the lower housing plate comes assembled with new bushing and gear. This is now the third one of these expensive mixers I have repaired, word got out that I fix them, and this is a very common problem. Repairs have been for friends and Church, so I don't charge any labor, it's kind of fun, messy, but fun. Note to Kitchen Aid: Please strengthen lower gear case.

After trying to make a batch of heavy frosting, my KitchenAid mixer final stopped turning. After watching a video of how to change the grease in a similar model on PartsSelect and seeing it wasn't that hard to take apart, I decided to give it a try myself. Removing the cover exposed a completely worn gear drive. Luckily, it was easy to determine which parts needed replacing and PartSelect sent them in no time. Once I put everything back together, it sounded terrible which was pretty tough to take. As it turned out, the problem was flecks of metal from the gear were still in the grease and were getting caught in the mechanism. Once I thoroughly cleaned all the grease out and gave it some fresh grease the machine worked great. Much better than before. I only wish I had swapped the grease out at the same time. Thank you PartsSelect for saving me hundreds of dollars on a new machine!