4KV25H0XBU5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken thrust bearing kit caused damage to the worn gear
Disassambled the gear-train.Removed all broken pieces and grease from gear case. Cleaned gear case and all parts. Reassembled gear-train with new parts and packed all with suitable quantity of new grease. Test run with variable speeds assuming working smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Pittsford, NY
- Parts Used:
- W11086780
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Gear Stripped was trying to replace
Could not get it properly installed. Had to take to a repair center for completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Jamestown, ND
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gear teeth worn off worm gear
replace worm gear
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reza from STAMFORD, CT
- Parts Used:
- W11192795
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The mixer started making a loud knocking noise
Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from LARGO, FL
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madeleine from NEW YORK, NY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from North Olmsted, OH
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Part broken
Easy thanks to your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from SOUTH ELGIN, IL
- Parts Used:
- W11192795
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken gears
Fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from KIRBYVILLE, TX
- Parts Used:
- WP9706648
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor knob
Watched utube
video how to repair and ordered part, easy
video how to repair and ordered part, easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from STRAWBERRY PT, IA
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Speed control switch went out
Unplugged wires from old switch, plugged them into the new switch. The new Switch have the mounting brackets in different places from the old one. Be sure to match up the numbers by the posts with the correct wires
Was this instruction helpful to you?
Thank you for voting!
Bad control switch, striped worm follower gear.
Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EBEN from WEST PALM BCH, FL
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
unit would only operate at high speed
using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
Was this instruction helpful to you?
Thank you for voting!
Gear housing cracked, gear had nic in it
Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CEDAR CREEK, TX
- Parts Used:
- 8212396
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken gear case.
Remove and replace gear case. Apply food grade grease secure with screws.
Was this instruction helpful to you?
Thank you for voting!