KM25G0XWH4 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Worn gears
Took mixer apart and then the gear compartment. inspected components. Replaced the worn gears and re-greased the new parts. Put the gear compartment back together, tested the operation of the unit and then replaced the rest of mixer, re-tested and declared victory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from san antonio, TX
- Parts Used:
- WPW10247536, WP9709231, W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Gears worn and Speed control sensor
I have to thank you at Partselect.com. You happen to help me help other people. Now I have several people bringing me their Kitchenaids to me instead of sending them in. I replaced two worm gears on a Kitchenaid 6 and the Hall sensor on a Kitchenaid 5. Very easy to do. Next week I have another Kitchenaid 5 to replace the motor on. Thankyou again for having the parts I need
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PJ from Rome, GA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Part to KitchenAid Mixer
Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from saint simons island, GA
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
speed controll switch. would start and stop on its own.
replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Salem, IL
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The thumb screw plastic came off
Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Crivitz, WI
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had lost the thumb screw
I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Thornton, NH
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
worn gear causing slippage under load
removed cover. Removed cover over gears. Used lock washer pliers to remove lock washer. Took out gears. Cleaned metal shavings from old gear and grease. Reassembled using new gear. Took about 15 minutes and saved $$ over sending mixer out for the repair.
Was this instruction helpful to you?
Thank you for voting!
Mixer wouldn't slow down
I unplugged the mixer, then I removed the Phillips screw holding the beauty ring, then removed the 4 screws that hold the motor housing together. I removed the housing top, and unscrewed the speed control switch. I marked each one of the connectors of the switch (there are 4) 1-4 then disconnected the speed sensor from the switch and the motor. Replaced the new sensor and connected that to the new speed control switch. reconnected the connectors to the terminals I took them from ( 1 - 4 ) screwed it into place. replaced the top motor housing, I screwed that back with the four screws. replaced the beauty ring and screw. plugged it in and tested it and it was like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from RIVERSIDE, CA
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer goes full speed even when on low setting.
Removed one screw to remove deco band around mixer body. Removed four screws under band to remove mixer top. Removed two screws holding switch. Removed wires one at a time putting them in the same position on the new switch. Re-attached switch, mixer top, and deco band. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Los Angeles, CA
- Parts Used:
- W10807813
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Paint flaking off beater; flakes got into food.
I used the website to find the appliance, but had to call the help number because the model number had one extra 'B'. I was told that this was only for the color (black). Using the chart I found the part number and ordered it. It arrived in about 3 days (regular shipping). No repair was needed beyond snapping the new part in to replace the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from wilton, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
didn't turn
ordered the part and put in in with the help from the instant repairman
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie Ann from Dover, MA
- Parts Used:
- W10807813
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new mixer beaters
I replaced my kitchen Aid mixer beaters. I bought two replacement beaters. They fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Lynden, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Thumb screw
the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Santa Barbara, CA
- Parts Used:
- W10807813
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Paint was peeling off the old beater.
I put the beater in the mixer when I wanted to make a cake. I wouldn't call it a repair. The most amazing thing was that it arrived the day after I called and ordered it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathi from Roosevelt, UT
- Parts Used:
- W10807813
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
coating on beater coming off
took old off and new fit right in saved me over $300.00 for new mixer !
Was this instruction helpful to you?
Thank you for voting!