5KP2670-3 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- robert from san antonio, TX
- Parts Used:
- WPW10247536, WP9709231, W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Gears worn and Speed control sensor
I have to thank you at Partselect.com. You happen to help me help other people. Now I have several people bringing me their Kitchenaids to me instead of sending them in. I replaced two worm gears on a Kitchenaid 6 and the Hall sensor on a Kitchenaid 5. Very easy to do. Next week I have another Kitchenaid 5 to replace the motor on. Thankyou again for having the parts I need
Was this instruction helpful to you?
Thank you for voting!
Mixer wouldn't slow down
I unplugged the mixer, then I removed the Phillips screw holding the beauty ring, then removed the 4 screws that hold the motor housing together. I removed the housing top, and unscrewed the speed control switch. I marked each one of the connectors of the switch (there are 4) 1-4 then disconnected the speed sensor from the switch and the motor. Replaced the new sensor and connected that to the new speed control switch. reconnected the connectors to the terminals I took them from ( 1 - 4 ) screwed it into place. replaced the top motor housing, I screwed that back with the four screws. replaced the beauty ring and screw. plugged it in and tested it and it was like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Thornton, NH
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
worn gear causing slippage under load
removed cover. Removed cover over gears. Used lock washer pliers to remove lock washer. Took out gears. Cleaned metal shavings from old gear and grease. Reassembled using new gear. Took about 15 minutes and saved $$ over sending mixer out for the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Frankfort, IN
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Worn worm gear
The KitchenAid is "old school" in that it is held together with simple (but very stout) bolts and screws. I removed about 10 such fasteners, slipped off the gear retainer, and pulled it out. On Sunday, a very nice customer service rep helped me order the right part, but I did the rest on line in a matter of seconds. It shipped on Monday and arrived on Wednesday. Took about 10 minutes to put everything back. I REALLY WISH everything was this easy in 2012!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marjorie from juda, WI
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
head of screw was broken in half
I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie
Was this instruction helpful to you?
Thank you for voting!
Trouble with switch
removed top casing, removed old switch and sensor,and replaced with new ones. It was just a matter of a half dozen screws and unpluging 4 or 5 wires and then reversing the process. Couldn't be easier. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from RIVERSIDE, CA
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer goes full speed even when on low setting.
Removed one screw to remove deco band around mixer body. Removed four screws under band to remove mixer top. Removed two screws holding switch. Removed wires one at a time putting them in the same position on the new switch. Re-attached switch, mixer top, and deco band. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!