4KN15E1XSL1 KitchenAid Mixer - Instructions

1. Removed the decorative band then the upper motor cover.
2. Removed the upper gear case cover. Found one of the two alignment pins broken.
3. Inspected gears.
4. Cleaned out old grease.
5. Repacked with new food grade grease.
6. Reassembled.

Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.

Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .

Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.

Remover screws from top. Used snap ring pliers to remove snap ring replaced gear and reassemblied.

Fast

When I ordered a replacement assembly, I was sent a "new" replacement. As I had read up on your site to number the 5 wires BEFORE I removed them, this was a great idea. The new assembly was wired differently than the original board. Although no install instructions came with the new part, it was just a matter of connecting the NUMBERED wires to the new configuration. The first time I fired it up after plugging everything in, nothing happened! I removed all the plug-in wires and reinstalled to ensure I had not gotten a tight connection because of the plastic covers over the end connectors. On my second try, everything worked as advertised! VIOLA!!!! It was a bit tough because of the tight spaces within the motor housing and the new wire routing. Just take pictures of the area BEFORE you disconnect anything and you should do o.k., since I did. 20 minutes.

Just followed the video.amazing!!got my kitchen aid back.

I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.

I went to YouTube and there are several Mixer repair videos that go through step by step. Four ounces of food sate grease is also required as the grease must be changed. This appears to be a a common problem. One issue that I discovered is that the old planetary had an Oring in the shaft The replacement parts do not. They must have changed the design so please make sure that food safe grease is used.

First you need to remove the aluminum ring around the housing by using a Phillips screwdriver and removing one screw. You will then have 4 screws around the housing to remove. Once the screws are removed lift the housing and set aside. At the front of the machine there is a housing that encloses the gears. Remove the 4 screws, lift the housing and set aside. At this point you will see the gears and on the shaft there is a snap ring that needs to be removed. Once the snap ring is removed tap the shaft down and remove it from the bottom. To assemble insert the new planetary and reverse the steps to reassemble.

Remove and replace gear case. Apply food grade grease secure with screws.

Taking apart the machine is really easy. I was worried the grease would have spilled all over the places, but when the machine is cool, the grease is solid, so no spill. Replace the parts is quite straightforward, and there are plenty of tutorials on line. The only tip is that the grease used by KitchenAid is dark, and it is not easy to see all the small parts when you take the gearbox apart, so pay attention at what you do and at what you throw away... when I got to put it back together I missed a special concave washer which must have been trapped in the grease. Other than that... it has been an easy repair, the mixer is back up and running and I saved a ton on $$$

Could not get it properly installed. Had to take to a repair center for completion.

I replaced the electronic speed control and the plastic housing with a new metal housing, both fitting perfectly and easily installed. Excellent replacement parts.