All Installation Instructions for KitchenAid Mixer 4KV25H0XBK5

Customer:: PJ from Rome, GA
Parts Used:: WP9709194
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Broken Part to KitchenAid Mixer

Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again

Was this instruction helpful to you?

Customer:: brian from saint simons island, GA
Parts Used:: WP9706648
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

speed controll switch. would start and stop on its own.

replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.

Was this instruction helpful to you?

Customer:: Jane from Crivitz, WI
Parts Used:: WP9709194
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

I had lost the thumb screw

I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.

Was this instruction helpful to you?

Customer:: Linda from Lynden, WA
Parts Used:: WP9709194
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Thumb screw

the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install

Was this instruction helpful to you?

Customer:: Paul from Manns Choice, PA
Parts Used:: W11086780
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

Teeth worn/broken off part of the worm gear

Removed shroud and gear case top. No snap-ring pliers, so I used two small vice grips, one on each lobe, and spread and "worried" the ring up the shaft. Changed out all ghe grease in case of metal chips. Put it back tegether. Works fine.

Was this instruction helpful to you?

Customer:: John from Ewing, NJ
Parts Used:: WPW10170081, WPW10170080, 8212396, WP9709511, WP9708175, WP9709231, WP9707223, W11086780, WP67500-55, WP16897, W11192795, W11192795, W11200218
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins

Stripped Worm Gear

Had to repalce all the parts due to several issues caused the main problem. I am a mechanic by trade so it was easy to repair.

Was this instruction helpful to you?

Customer:: Holger from Spokane, WA
Parts Used:: W11192795
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Gear Stripped

I had previously ordered several other gears after I found one of the worm gears stripped. After putting it all back together, the one major gear in the unit that I had not replaced because it looked fine, the bevel gear, also stripped. Learning experience: this is a unit worth several hundred dollars, so don't skimp on a $4 part. Once you work on this thing, you might as well spend a few bucks more and replace ALL the gears - even if they look like they are okay. Furthermore, if you only take 15 minutes to do this repair, as some on this site suggest, you are probably not cleaning the old grease carefully enough. Make sure you properly clean out the old grease to remove any metal from stripped gears, and use a good quality grease to re-pack the gear case.

Was this instruction helpful to you?

Customer:: robert from wilton, CA
Parts Used:: W11086780
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

didn't turn

ordered the part and put in in with the help from the instant repairman

Was this instruction helpful to you?

Customer:: Rodney from Thornton, NH
Parts Used:: W11086780
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

worn gear causing slippage under load

removed cover. Removed cover over gears. Used lock washer pliers to remove lock washer. Took out gears. Cleaned metal shavings from old gear and grease. Reassembled using new gear. Took about 15 minutes and saved $$ over sending mixer out for the repair.

Was this instruction helpful to you?

Customer:: Sal from STATEN ISLAND, NY
Parts Used:: WP9706648, WP9706648
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Mixer wouldn't slow down

I unplugged the mixer, then I removed the Phillips screw holding the beauty ring, then removed the 4 screws that hold the motor housing together. I removed the housing top, and unscrewed the speed control switch. I marked each one of the connectors of the switch (there are 4) 1-4 then disconnected the speed sensor from the switch and the motor. Replaced the new sensor and connected that to the new speed control switch. reconnected the connectors to the terminals I took them from ( 1 - 4 ) screwed it into place. replaced the top motor housing, I screwed that back with the four screws. replaced the beauty ring and screw. plugged it in and tested it and it was like new

Was this instruction helpful to you?

Customer:: JOHN from RIVERSIDE, CA
Parts Used:: WP9706648
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Mixer goes full speed even when on low setting.

Removed one screw to remove deco band around mixer body. Removed four screws under band to remove mixer top. Removed two screws holding switch. Removed wires one at a time putting them in the same position on the new switch. Re-attached switch, mixer top, and deco band. Works perfectly.

Was this instruction helpful to you?

Customer:: Rick from Warwick, RI
Parts Used:: WP9703680
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Mixer would not fully rotate under any load

Removing the cover of the mixers "guts", it was immediate evident the a major gear had lost a few of its "teeth". Parts Select clearly offered the required part of this $300 mixer for a favorable price. I was fully impressed that it arrived within 4 days or my ordering the part. I simply exchanged the damaged gear and restored the mixer to service and I'm fully impressed with the Parts Select Company for their swift response to my needs.

Was this instruction helpful to you?

Customer:: Johna from Ketchikan, AK
Parts Used:: W11086780
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Stripped worm gear

Looked at the schematic for this model on Parts Select. Removed Aluminum band screw, removed the 4 screws that hold the top of the mixer. Lifted the top off. Removed 4 screws and lifted the gear case. Removed snap ring and took off tapered gear. Removed pin and removed worm gear. Picked out the metal, in the grease, from the old worm gear, using a magnet then inserted new worm gear and put it back together in reverse order. There was plenty of grease and didn't need to add any.

Was this instruction helpful to you?

Customer:: Mark from Florence, OR
Parts Used:: WP9707223, W11086780, WP9703680, W11192795
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

bevel gear was stripped

opened the mixer.. all screws in kitchaid are the same so not to worry... opened up and replaced the gears... and put it back together... diagram helped in that front and rear bearings of connecting gear are the same # on diagram it is easy to confuse when you put it back together, but the item number and description of each helped make sure it was in the right place. Otherwise... time to fix would have been less....

Was this instruction helpful to you?

Customer:: Craig from Cawker City, KS
Parts Used:: W11086780
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

stripped gear.

took mixer cover off, took gear box cover off, removed gears, replaced gears, replaced covers, made cookies, no problem!!

Was this instruction helpful to you?

4KV25H0XBK5 KitchenAid Mixer - Instructions