4KV25H0XER4 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mixer blade did not turn, striped gears.
Replaced the worm gears. Original were ground down as if they were not seated correctly. Ordered the parts and swapped them out. I do not own a retaining clip removal tool. This was the most difficult, trying to open the clip using 2 needle nose pliers. It made the repair time longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from SAINT LOUIS, MO
- Parts Used:
- WP9708649
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
needed to replace rubber foot on mixer
The insertion part of the foot was tapered to fit in the hole in the mixer. Simple pressure was not the answer. So I used a small key, placed it on the bottom of the foot, after applying a little vegetable oil on the foot, and tapped it into place. Worked well.Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FLINT, MI
- Parts Used:
- W11200218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad gears
Easily took apart and replaced gears. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bunny from WAMEGO, KS
- Parts Used:
- W11086780, WP9703680, WP67500-55, W11084660
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Worm gear wore out
Dismantled gear box pulled all gears out and replaced worm gears
Was this instruction helpful to you?
Thank you for voting!
Broken thrust bearing kit caused damage to the worn gear
Disassambled the gear-train.Removed all broken pieces and grease from gear case. Cleaned gear case and all parts. Reassembled gear-train with new parts and packed all with suitable quantity of new grease. Test run with variable speeds assuming working smoothly.
Was this instruction helpful to you?
Thank you for voting!
Worm gear had stripped so changed out several gears and parts
Opened the gear housing and removed all gears. Cleaned out all grease. Biggest issue was getting the retaining ring; very tight. Gears were difficult to pull easily. In replacing gears they did not sit easily and took a little rubber hammer to re position worm and upper gear. Be sure to have the right grease for food devices and don’t under grease. And have patience of which I have a short supply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Mentone, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.
Was this instruction helpful to you?
Thank you for voting!
mixer was very noisy when running and made a horrible grinding sound
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from North Olmsted, OH
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Part broken
Easy thanks to your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Pittsford, NY
- Parts Used:
- W11086780
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Gear Stripped was trying to replace
Could not get it properly installed. Had to take to a repair center for completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Jamestown, ND
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gear teeth worn off worm gear
replace worm gear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reza from STAMFORD, CT
- Parts Used:
- W11192795
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The mixer started making a loud knocking noise
Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from LARGO, FL
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from STRAWBERRY PT, IA
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Speed control switch went out
Unplugged wires from old switch, plugged them into the new switch. The new Switch have the mounting brackets in different places from the old one. Be sure to match up the numbers by the posts with the correct wires
Was this instruction helpful to you?
Thank you for voting!