Models > KB26G1XTG5 > Instructions

KB26G1XTG5 KitchenAid Mixer - Instructions

Jump to:

All Instructions for the KB26G1XTG5

Customer:: Joseph from Mentone, CA
Parts Used:: W11086780
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

none

followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Gary from Hamburg, MN
Parts Used:: WPW10170081, WPW10170080, 8212396, WP9709511, WP9709231, W11086780, WP9703445
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

gears and bearing failure

inspected and replaced worn components

4 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: conradt from el paso, TX
Parts Used:: 8212396, WP9709511, W11086780
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Last repairperson broke the top cover of the gearcase ; still need this part .

Easy ; remove belt ( 1 screw ) remove cover , and there is the complete drive . I still need the top plastic cover which is cracked and broken where the bolts go through . Please quote this part .Conradt

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jamie from Jamestown, ND
Parts Used:: W11086780
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

gear teeth worn off worm gear

replace worm gear

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jerry from Southport, NC
Parts Used:: WP9709231, W11086780
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Worm gear stripped.

Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Russell from NEW LONDON, CT
Parts Used:: 8212396
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

The stand mixer would not rotate at low speed. Upon disassembly found one of the two alignment pins of the upper gear case broken.

1. Removed the decorative band then the upper motor cover.
2. Removed the upper gear case cover. Found one of the two alignment pins broken.
3. Inspected gears.
4. Cleaned out old grease.
5. Repacked with new food grade grease.
6. Reassembled.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Robert from PEORIA, AZ
Parts Used:: W11086780
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

Stripped Gear Mixer would not mix

I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: FRANCISCO from SAN BENITO, TX
Parts Used:: WP9706648
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins

REPLACE SPEED CONTROL SWITCH

REPLACE SPPED CONTROL SWITCH

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: EBEN from WEST PALM BCH, FL
Parts Used:: WP9706648
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

unit would only operate at high speed

using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Bruce from EUREKA, CA
Parts Used:: W11086780, WP9703445, WP16897
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

Bad control switch, striped worm follower gear.

Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: John from ST AUGUSTINE, FL
Parts Used:: W11192795, 8212396
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

attachment planetary gears stripped

removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Karl from Hammond Ranch, CA
Parts Used:: W11192795, W11086780, WP9707223, WP16897
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers, Socket set, Wrench set

Planetary Pinion Gear Assembly had dropped down

The repair was easy, I only had to order new gear assembly parts and to replace the associated worn parts (shaft, pin, and gears).

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Richard from Harrodsburg, KY
Parts Used:: WP9706648
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers

Speed switch bad and Initially thought new part was wrong!

At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Reza from STAMFORD, CT
Parts Used:: W11192795
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

The mixer started making a loud knocking noise

Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: ROBERT from LARGO, FL
Parts Used:: WP9706885
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins

white plastic part on the lifter handle

Took off all the screws to open the mixer and install the new parts.

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

All Instructions for the KB26G1XTG5