Models > KP26M1XGA5 > Instructions

KP26M1XGA5 KitchenAid Mixer - Instructions

Jump to:

All Instructions for the KP26M1XGA5
106 - 120 of 195
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Judith from Turtle Lake, WI
Parts Used:
W11192795
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Gears had stripped due to housing crack and movement
Took top apart and installed new housing and two gears. Reassembled
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
CHRISTINA from NEW GLOUCESTER, ME
Parts Used:
8212396
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Plastic gear cover broken
Removed plastic cover, removed grease and put in new mixer and put new cover back on.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from York, PA
Parts Used:
8212396, WP9709511, W11192795, W11192795
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Grinding sound
Replaced cracked plastic gearcase/transmission with new medal one and replaced hub bevel gear attachment, bevel gear and gasket.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Brookings, OR
Parts Used:
W11086780
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
mixer beater quite
disassembled unit gear head and replaced broken part, then reassembled
0 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mitchell from Santa Fe, NM
Parts Used:
W11086780
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Mixer would not spin, worm gear worn out.
The repair is actually quite simple. The Snap Ring Pliers are essential. Make sure you clean out all the old grease in the machine and replace with new grease. The metal dust will act like sandpaper and destroy your new gear. There are several videos on YouTube which go through the process of repair and part replacement, I found these quite helpful. Good luck! DIY!!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Johnna from Childress, TX
Parts Used:
W11200218
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Stripped worm follower gear.
Watched the video. Ordered the parts. Watched the video again. Replaced the worm follower gear and bearings on the worm gear. Added grease. Installed new gear housing. Put it all back together and tested. Works like new. Now I get cakes and goodies again and have a happy wife who thinks I'm super handyman. Thanks
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronny from Clearwater, KS
Parts Used:
WP9707223, W11086780
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Worm Gear teeth was stripped
Removed top cover, remove snap-ring on shaft, slide top gear and worm gear off. Clean all the grease out and clean parts. Installed new worm gear and parts. Repacked with new grease, careful not to much, leaving room for expansion.
Was this instruction helpful to you?
Thank you for voting!
Customer:
carole from new braunfels, TX
Parts Used:
W11086780, W11192795, W11192795, W11200218
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
gears stripped
watched the youtube video on how to repair a Kitchenaid Pro 600.
Was this instruction helpful to you?
Thank you for voting!
Customer:
vicki from topeka, KS
Parts Used:
W11123171
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
part broke
Husband easily put back together and it works great.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda from Lynden, WA
Parts Used:
WP9709194
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Thumb screw
the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Charlotte, NC
Parts Used:
W11646967
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
missing part
just attached it
Was this instruction helpful to you?
Thank you for voting!
Customer:
PJ from Rome, GA
Parts Used:
WP9709194
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Part to KitchenAid Mixer
Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from wilton, CA
Parts Used:
W11086780
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
didn't turn
ordered the part and put in in with the help from the instant repairman
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karen from Salem, IL
Parts Used:
WP9709194
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The thumb screw plastic came off
Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jane from Crivitz, WI
Parts Used:
WP9709194
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I had lost the thumb screw
I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KP26M1XGA5
106 - 120 of 195