KSM85PSBK0 KitchenAid Mixer - Instructions

Removed the rear cover to inspect the speed board. Replaced motor brushes and noticed the motor body nuts were loose and 1 was completely off. Cleaned up speed board and replaced the motor body nuts, tightened with nutdriver, adjusted speedboard governor screws and with new motor brushes worked like a charm. The very rough sounding motor noise was gone and the mixer has not operated so quietly ever.

Found control backplate out of adjustment. Should be nominal 3/8".Broken speed control spring which attaches to backplate bottom.
I recommend Loctite Blue to complement locknut's when adjusting RPM of "Stir" speed

Watched a couple of youtube videos and it was easy.

Followed instructions found onllne at Kitchenaid.com and replaced seals with parts obtained from PartSelect.

First i went to the Kitchen Aid web site and found a video on how to take a part the mixer. Followed the instructions from the video and it was very easy. The grease in the machine was black so i cleaned it out of the transmission and repack it with hi-heat wheel bearing grease that i got from a auto parts store it took about a 1/2 lb. then put the gasket in and back together and put the o-ring on. Have run for awhile and it is ok. Want to say that these are very well built machine.

I watched the university of YouTube videos, and followed their instructions.

Unscrewed the existing screw cap, put the new one in place, replaced the screws. So easy!

Simply removed damaged gears. Very simple to do. Ordered gears. Replaced gears. Both working well ( so far. ) Machines are easy to dismantle. Just be sure to put the screws back in the holes you took them out of when dismantling...no lost screws. On the smaller model, took pictures of the wire positions to be sure they were replaced in the proper order. Larger model had no wires to remove.

Got a harvest gold mixer from g maw and thought a project would be nice we have several of these mixers in the family i knew a 2 prong cord was not safe so i took apart the mixer and wanted to regrease it just give a lookie to see what i needed and then i decided after watching video on y tube to convert to a solid state.

Parts select as a whole has been very understanding as a whole and i will continue to get parts thru them they are genuine parts which is something i had to have i have 90% of my parts for a full overhaul we just cannot get the parts delivered fedex and usps i specify the address and they deliver 2 blocks east of the house thanks for honest neighbors usps was late as usual like i said parts select is outstanding at placing the order and appliances can be fixed super simple with the right tools the concern is with the fedex and usps now they are shorthanded but lets be real but when you deliver a package just triple check it is the right house !

Repair went well after I figured out how to dis-assemble the mixer. Used straight & phillips screwdrivers and a small hammer & punch to drive out 3 pins. Ordered part# PS734233 pinion & shaft as shown in the parts page, it arrived on schedule, received part # 240210-2. Only problem was the new pinion had 10 teeth, the old/failed pinion had 11 teeth. Could not learn from anyone I called at PartsSelect or Whirlpool if the 10 tooth pinion was the correct part to use.
The teeth appeared to mesh with the mating gear,
installed the new pinion, reassembled and it worked fine. Not sure if it made a noticable difference in the output shaft speed.

Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!

Removed back cover, disconnected the 2 push-on connectors, removed ground wire screw. Reversed the process to install new cord.

The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!

I replaced the phase control board because the mixer had only
one speed and was surging. I noticed from other posts that it
is important to note the setting of the speed plate before you
remove it in order to remove the phase control board. Also be
careful removing the associated 'slip-on' terminals as it would
be easy to damage the speed plate. If I ever do this again I
will go ahead and replace the speed plate, probably the cheapest
item to replace. The operation was a success and the mixer is
back in business. Thanks.

INSTALLED PHASE CONTROL BOARD AND SPEED CONTROL PLATE, BOTH AT SAME TIME
Your DYI video was helpful, especially holding the spring with a cloth. Also good for fine tuning to get the speed exact