5KPM50BGR4 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David l from Heath, OH
- Parts Used:
- WPW10731415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Install as per any accessory
Ordered part on Sunday, arrived on Tuesday morning. Mixer ready to use after washing and installing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from St. Cloud, WI
- Parts Used:
- WP116287
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new brushes for a mixer
Easy to locate part I needed (brushes)..great diagrams Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marjorie from juda, WI
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
head of screw was broken in half
I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Statesboro, GA
- Parts Used:
- WPW10731415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A broken part
I went to the web site and had a new part ordered within minutes and received it within a couple days! It could not have been easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dantirb from CLINTON, MI
- Parts Used:
- WPW10674621, WP3182857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring latch bad
easiest fix I ever did Thank You for your fast service and high quality of your products. I will be a repeat customer and recommend you to people I know. Thank You Daniel
Was this instruction helpful to you?
Thank you for voting!
Replaced main gears
1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Cantfeild, OH
- Parts Used:
- WP241764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The arm to mixing bowl would not lift bowl
Took the four screws under mix off. Remove old broken part and slip in the new one and rue screw head back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REID from BELLEVUE, WA
- Parts Used:
- WP9709276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plastic knob on speed control lever was lost
The knob was attached to the new lever. I began to disassemble the mixer case so that I could replace the lever. However, it soon became apparent that this would be a major project involving many components and potential problems in getting the unit back together. Since all I wanted was to replace the knob, I simply knocked it off the new lever and forced it onto the old one. It is hard for me to understand why Kitchenaid would not make just the knob available.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathi from Roosevelt, UT
- Parts Used:
- W10807813
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
coating on beater coming off
took old off and new fit right in saved me over $300.00 for new mixer !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tolland, CT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sticky back disc on Orbital sander came apart (from old age )
remove 3 screws ,remove old sanding disc replace with new installl screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Santa Barbara, CA
- Parts Used:
- W10807813
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Paint was peeling off the old beater.
I put the beater in the mixer when I wanted to make a cake. I wouldn't call it a repair. The most amazing thing was that it arrived the day after I called and ordered it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Shelby Twp., MI
- Parts Used:
- WP241764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
bowl lift arm would lock into place
removed the top of the mixer from the stand. I left the broken piece in place until the new part arrived so I would know exactly how the part fit in. I used the punch & hammer to remove the pin then removed the part with needle nose pliers. I put on the new part, checked to see that it worked and reinstalled the top of the mixer to the base. It was really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie Ann from Dover, MA
- Parts Used:
- W10807813
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new mixer beaters
I replaced my kitchen Aid mixer beaters. I bought two replacement beaters. They fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Lynden, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Thumb screw
the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Reno, NV
- Parts Used:
- WPW10380496
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor would not turn on
Initially removed carbon brushes then inserted the new carbon brushes. The motor still did not turn on. Then I removed the brushes again, used a flashlight to look in the hole where the carbon brushes are installed. I noticed that there was a square notch on one side of the hole. I then reinstalled the carbon brushes, ensuring that the beveled side of the carbon brush was installed so it lines up with the square notch. This allows the carbon brushes to touch the motor. I turned the unit on and it worked.
Was this instruction helpful to you?
Thank you for voting!