4KG25H3XOB5 KitchenAid Mixer - Instructions

Replaced cracked plastic gearcase/transmission with new medal one and replaced hub bevel gear attachment, bevel gear and gasket.

disassembled unit gear head and replaced broken part, then reassembled

watched the youtube video on how to repair a Kitchenaid Pro 600.

The repair is actually quite simple. The Snap Ring Pliers are essential. Make sure you clean out all the old grease in the machine and replace with new grease. The metal dust will act like sandpaper and destroy your new gear. There are several videos on YouTube which go through the process of repair and part replacement, I found these quite helpful. Good luck! DIY!!!!

Removed top cover, remove snap-ring on shaft, slide top gear and worm gear off. Clean all the grease out and clean parts. Installed new worm gear and parts. Repacked with new grease, careful not to much, leaving room for expansion.

Watched the video. Ordered the parts. Watched the video again. Replaced the worm follower gear and bearings on the worm gear. Added grease. Installed new gear housing. Put it all back together and tested. Works like new. Now I get cakes and goodies again and have a happy wife who thinks I'm super handyman. Thanks

Removed the cover. Removed the gear assembly cover.. Extracted the C clip with a tool. Removed the bevel gear. Pushed out the dowel pin. Used rubber mallet to push the shaft off the worm gear. Replaced the washer and the worm gear. Used a 1/2" diameter PVC, 3" long over the shaft and on the gear to push back the shaft through the gear with rubber mallet. Pushed back the dowel pin. Reinstalled the C clip. Replaced broken hub bevel gear. Added more grease. Placed the gear cover with 4 screws just tight enough to hold the cover but still allows movement. Turned the mixer to the lowest speed. Allow the cover to self adjust so that the gears have the smoothest sound. Tightened the screws while while maintaining the smooth sound. Turned off the power. Replaced the cover.

Remove Beaty band, one screw. Remove four screws holding top. Remove worm gear, by simply lifting it out. Removed all grease. Repacked with fresh grease. Take out gear case/ transmission bearing, clear all old grease, repack with new grease. Install into new gear case housing. Assemble, and Repack new worm gear and front and rear worm gear bearings, utilize old washers (2), and one small ball bearing washer. Rotate worn gear and bushing to spread the new grease throughout the gears. Replace top cover, four screws . Replace beauty ring, one screw. Run unit for 20 to 30 seconds, under no load to distribute the new grease. Works like a charm. 45 minutes to one hour. To complete.

Used the meat grinder attachment, with the retaining ring too tight for the motor to turn the augur, so a gear stripped and the mixer would not run. I opened the mixer top, removed the transmission cover, removed enough grease to diagnose the problem (6 teeth stripped off the steel worm gear). I ordered a replacement steel worm gear and, while I was at it, a new retaining ring, bevel gear, retaining pin and the large planetary gear, as I could not tell the condition of these until I disassembled the whole gear train. I then removed the gear train components (needed a snap ring pliers to remove the retaining ring -- I don't recommend trying to remove it with an y other tool), washed them in acetone, cleaned out the transmission case and went over it with a magnet to get stray gear tooth remnants, replaced the worm and bevel gears and reassembled, using the original planetary gear, retaining pin and retaining ring. Filled the bottom of the transmission with planetary grease first, then, once the gear train had been replaced, slathered a big pile of grease over it, replaced the transmission cover. The machine then ran perfectly, so I replaced the mixer's top cover and decorative band and was back in business mixing with it about 30 minutes after cleaning the last of the grease off my hands. I should mention, I used a LOT of paper towels for this job. This was a fun job and I was sorry that it was so easy to do, as I enjoy working with gears and grease.

took mixer apart down to removal of gear case cover.upon removal of this cover found the bevel gear and hub bevel gear chewed up .removed them both then replaced them both.and also had to solve a clearence problem between the 2 gears they were too loosely meshing. so had to push the hub retainer closer to take up the meshing slack.not sure my repair will hold but i have another set of gears and another solution that will surely fix it.

First of all, go to the web site and download the schematics of the model #. It will show all the parts and part #s. Secondly watch a u tube video of the actual strip down process of the professional 600 series stand mixer. With this knowledge, do one of two processes 1: strip down the machine, remove the gears and check for defects- order parts. Or 2: replace all the parts( little money) and have a totally refurbished , smooth running mixer. I kept the good used gears for spares. I replaced 90 % of the internals ( including motor) and have a smooth running machine. I initially burned out the mother 2 months after initial purchase, sent it back under warentee, and received it back . Wen I stripped it down 10 years later, there was very little grease in the gear housing. This is what probable ruined the gears. Use plenty of grease in the housing and gears. The grease is one of the most expensive items, but you can't find it anywhere, so order it, along with everything else, from Parts Select.

the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install

Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again

ordered the part and put in in with the help from the instant repairman

I tried to use the broken mixer paddle for almost a year before I checked out the part broken on line. I easily found the part, and it arrived within a week--and fit perfectly! Thank you for making it so easy to do on line!