KD2661 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
mixer was very noisy when running and made a horrible grinding sound
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Mentone, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madeleine from NEW YORK, NY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Jamestown, ND
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gear teeth worn off worm gear
replace worm gear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Pittsford, NY
- Parts Used:
- W11086780
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Gear Stripped was trying to replace
Could not get it properly installed. Had to take to a repair center for completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reza from STAMFORD, CT
- Parts Used:
- W11192795
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The mixer started making a loud knocking noise
Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from LARGO, FL
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
Was this instruction helpful to you?
Thank you for voting!
Gear housing cracked, gear had nic in it
Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from KIRBYVILLE, TX
- Parts Used:
- WP9706648
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor knob
Watched utube
video how to repair and ordered part, easy
video how to repair and ordered part, easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from STRAWBERRY PT, IA
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Speed control switch went out
Unplugged wires from old switch, plugged them into the new switch. The new Switch have the mounting brackets in different places from the old one. Be sure to match up the numbers by the posts with the correct wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from SOUTH ELGIN, IL
- Parts Used:
- W11192795
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken gears
Fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from North Olmsted, OH
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Part broken
Easy thanks to your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Harrodsburg, KY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Speed switch bad and Initially thought new part was wrong!
At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.
Was this instruction helpful to you?
Thank you for voting!
attachment planetary gears stripped
removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.
Reassembled mixer.
Was this instruction helpful to you?
Thank you for voting!