4KSM150PSTG0 KitchenAid Mixer - Instructions

Inserted new pin and tightened set screw.

Followed step-by-step video instructions for dis-assembly/reassembly found at ereplacementparts.com. All went well except when driving out the pin that holds the worm gear in the tower. The video wasn't exactly clear enough about what position the pin should be in when driving it out and I inadvertently drove the pin out so that it was trapped inside the tower assembly. Result? I had to bend the pin to get it out, causing an extra expenditure and wait time to order a new pin. So, lesson learned: be sure the pin is horizontal to the tower and not perpendicular to when driving the pin out. Also, I found that having the mixer apart was a good time to replace the grease in the housing. I don't think it would be required to replace the grease at this time but I was worried that pieces of the old worm gear could remain in the grease and possible get jammed in the gears after repairs were completed. Be sure to get a "food grade" grease not grease from your local auto parts store! The table knife was the best tool to use to remove the grease and to smear the grease all over the internal gears when replacing it.

I disassembled the mixer using a YouTube video as a guide. Disassembly was easy, as everything was held together with pins and threaded fasteners, and all electrical connections were plug-on.

Cleaning out the old grease was messy and time-consuming. I used a putty knife, screwdrivers (used them like small putty knives in the crevasses), paper towels, and finally, small cloths dampened with alcohol. After about a hour (maybe 90 minutes) everything actually looked like new.

I originally diagnosed the problem as the plastic gear loosening up from it's hub, so I ordered the complete gear tower assembly. It turned out not to be the problem- the gears were fine. With the gears removed to eliminate load, I applied power and saw that the original symptom was still there.

Further research turned up that this symptom is more likely a failed field coil, or possibly the phase control board. I ordered both from PartSelect. In the meantime, I tested the armature by measuring the resistance across the brushes as I slowly turned it by hand. At every angle, the resistance was about 7.5 ohms. Nothing lower, and no opens, so I'm pretty sure the armature is OK.

The phase control board arrived, but as of this writing, the field coil has been back ordered for almost a month. While I waited, I tried a partial reassembly of the head with the new board, and it worked! This weekend, I'll finish reassembly of the motor unit to the base/gearbox and calibrate the speed governor. In addition to the new gear tower and phase control board, it has new grease, seals, and both side levers (tilt and speed control) that had lost their knobs some time ago.

Hopefully it will be ready for another quarter century of use!

repair is farly simple just take your time, First attempted i didnt replace the speed covernor looked ok but had problems getting slow end to work properly decided to go ahead and install since i purchased it also and walia took care of the cogging problem. Good Luck

removed the screws holding the mixer housing and then removed the worn worm gear by removing the roll pin holding it on the shaft. Replaced the worm gear and inserted the pin that hole it in place. Replaced some of the gear grease and reassembled mixer. Went very easily. No problems at all.

unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!

New mixer bowl locks

Unplugged mixer. Removed screw holding cover on. Removed end seal. Inspected repair area for furhter damage. Installed new end seal and cover.

This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!

no instructions necessary

Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thanks for having our parts and guiding us with a diagram of the unit. Very helpful.

remove the back cover part # 36, remove the top cover part # 1 (by removing the chrome ring parate # 28, the mobile disk part # 25 and six screws part # 24). This done, remove the system parat # 38 to release the Pevel Pinion Center Gear part # 15 and remove the damaged part and put the new part. The install the removed parts in reverse order as they withdrew.

Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom

Watched a YouTube video to disassemble,from there went smoothly. One small piece of advice,take pictures with your smart phone during the process. Makes remembering easier.

Replace went good used the online video, my husband doesn't usually use any help but said the video helped him. Now my mixer works perfect. Also the price and shipping time was awesome.