KP26M8XCP5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mixer wouldn't slow down
I unplugged the mixer, then I removed the Phillips screw holding the beauty ring, then removed the 4 screws that hold the motor housing together. I removed the housing top, and unscrewed the speed control switch. I marked each one of the connectors of the switch (there are 4) 1-4 then disconnected the speed sensor from the switch and the motor. Replaced the new sensor and connected that to the new speed control switch. reconnected the connectors to the terminals I took them from ( 1 - 4 ) screwed it into place. replaced the top motor housing, I screwed that back with the four screws. replaced the beauty ring and screw. plugged it in and tested it and it was like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Lynden, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Thumb screw
the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Charlotte, NC
- Parts Used:
- W11646967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing part
just attached it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PJ from Rome, GA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Part to KitchenAid Mixer
Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from wilton, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
didn't turn
ordered the part and put in in with the help from the instant repairman
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from saint simons island, GA
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
speed controll switch. would start and stop on its own.
replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Salem, IL
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The thumb screw plastic came off
Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Crivitz, WI
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had lost the thumb screw
I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Warwick, RI
- Parts Used:
- WP9703680
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Mixer would not fully rotate under any load
Removing the cover of the mixers "guts", it was immediate evident the a major gear had lost a few of its "teeth". Parts Select clearly offered the required part of this $300 mixer for a favorable price. I was fully impressed that it arrived within 4 days or my ordering the part. I simply exchanged the damaged gear and restored the mixer to service and I'm fully impressed with the Parts Select Company for their swift response to my needs.
Was this instruction helpful to you?
Thank you for voting!
no power and have bad noise
remove the cover,take out four screw from gear box,remove the gear box,clean all gears,then you see damage gear,replace it ,install new grease.
Was this instruction helpful to you?
Thank you for voting!
bevel gear was stripped
opened the mixer.. all screws in kitchaid are the same so not to worry... opened up and replaced the gears... and put it back together... diagram helped in that front and rear bearings of connecting gear are the same # on diagram it is easy to confuse when you put it back together, but the item number and description of each helped make sure it was in the right place. Otherwise... time to fix would have been less....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Cawker City, KS
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stripped gear.
took mixer cover off, took gear box cover off, removed gears, replaced gears, replaced covers, made cookies, no problem!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Frankfort, IN
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Worn worm gear
The KitchenAid is "old school" in that it is held together with simple (but very stout) bolts and screws. I removed about 10 such fasteners, slipped off the gear retainer, and pulled it out. On Sunday, a very nice customer service rep helped me order the right part, but I did the rest on line in a matter of seconds. It shipped on Monday and arrived on Wednesday. Took about 10 minutes to put everything back. I REALLY WISH everything was this easy in 2012!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marjorie from juda, WI
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
head of screw was broken in half
I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie
Was this instruction helpful to you?
Thank you for voting!
Trouble with switch
removed top casing, removed old switch and sensor,and replaced with new ones. It was just a matter of a half dozen screws and unpluging 4 or 5 wires and then reversing the process. Couldn't be easier. thank you
Was this instruction helpful to you?
Thank you for voting!