KP26M1XCM5 KitchenAid Mixer - Instructions

Could not get it properly installed. Had to take to a repair center for completion.

I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.

Taking apart the machine is really easy. I was worried the grease would have spilled all over the places, but when the machine is cool, the grease is solid, so no spill. Replace the parts is quite straightforward, and there are plenty of tutorials on line. The only tip is that the grease used by KitchenAid is dark, and it is not easy to see all the small parts when you take the gearbox apart, so pay attention at what you do and at what you throw away... when I got to put it back together I missed a special concave washer which must have been trapped in the grease. Other than that... it has been an easy repair, the mixer is back up and running and I saved a ton on $$$

my hasband did the work and i an so happy it is working good for me now,

Called original Kitchen Aid and advised had been sold and to look for Kitched Aid on web. Found site, went to appliance diagram and obtained part number and ordered. When parts came in just unscrewed and replaced new feet.

I replaced the electronic speed control and the plastic housing with a new metal housing, both fitting perfectly and easily installed. Excellent replacement parts.

I removed the decorative band that covers the seam by removing 1 screw. I then removed the top portion of mixer by removing 4 square head screws. You will then see the gear housing in the front of the mixer. Remove the 4 screws holding that on. There are no spring that are going to pop out and you never know where they went, but be careful because there is a lot of grease and a gear that it just laying in there on the right side. You will see the stainless shaft with a couple on gear cogs on it. Remove the retaing spring from the shaft and pull the top gear off, it may be a little snug. You will then see the dowel pin, mine was sheared off but I could see where it was. Be sure to remove the broken pieces. Use the punch to knock out the remaining pin. Replace with new pin making sure it is evenly exposed on both side of the shaft. Replace the top gear, then the retaining spring, the the gear housing cover, then the mixer top cover and finally the decorative band. Be sure to unplug before you start. These mixers are expensive and expensive to have someone fix them. I ordered 2 pins because shipping is a little high and the pin is cheap. I fixed this for $17.00 total and have a spare pin.

the repair was very simple, total time probably 20 minutes.

Dear Customer Service,

I just would like to express my gratitude for your wonderful service. I received my part for my Kitchen aide mixer on time as promised. The part fit perfectly. Thanks you PartSelect for being there.
What a Great Site!

A Happy Customer!

took it apart. more grease all over. Put in all but one gear on the top. The noise is still there going to try to but the old bearings in and try again. I went back to the old worm gear and allmost all the noise stopped. I did put the new bearings in and the other gears. It seems that the gear on the worm gear was cut wrong. The noise was tear able. I tried the different parts I ordered one at a time. To find out which one stopped the noise. Every time I took a part I had grease all over. It took so long every time I put in a new part to put the trans back together again. I had grease all over.

The worm gear was defective. Called the 888 number and received excellent service. Said I would receive a refund and a new one in the mail.

Replaced cracked plastic gearcase/transmission with new medal one and replaced hub bevel gear attachment, bevel gear and gasket.

it just screw in.

Simply placed it in the slot and pounded until firmly in with a soft mallet. Thanks to your site I was able to find the piece easily and very inexpensively. Thank you so much. I would die if I couldn't fix this machine.

Remove screw at back of mixer,remove metal sleve and remove three more screws (front and sides. remove screws and plastic cap of gear box then remove holding ring in post and remove damaged ring installation is opposed of removal.