KP26M1XNP5 KitchenAid Mixer - Instructions

Unplugged wires from old switch, plugged them into the new switch. The new Switch have the mounting brackets in different places from the old one. Be sure to match up the numbers by the posts with the correct wires

Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.

so easy to remove the switch. I first marked the wires, 1-2-3-4 and then removed them from the old switch. removed the old switch and replaced with the new one and plugged in the wires as per markings. tried it out before replacing the top and it works perfectly. no longer timid about effecting repairs on my own. the diagrams on the website were a great help. this is a great company to do business with. part was here in 3 days.

1. Removed the decorative band then the upper motor cover.
2. Removed the upper gear case cover. Found one of the two alignment pins broken.
3. Inspected gears.
4. Cleaned out old grease.
5. Repacked with new food grade grease.
6. Reassembled.

removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.

The repair was easy, I only had to order new gear assembly parts and to replace the associated worn parts (shaft, pin, and gears).

At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.

I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.

Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.

Remove and replace gear case. Apply food grade grease secure with screws.

First you need to remove the aluminum ring around the housing by using a Phillips screwdriver and removing one screw. You will then have 4 screws around the housing to remove. Once the screws are removed lift the housing and set aside. At the front of the machine there is a housing that encloses the gears. Remove the 4 screws, lift the housing and set aside. At this point you will see the gears and on the shaft there is a snap ring that needs to be removed. Once the snap ring is removed tap the shaft down and remove it from the bottom. To assemble insert the new planetary and reverse the steps to reassemble.

I went to YouTube and there are several Mixer repair videos that go through step by step. Four ounces of food sate grease is also required as the grease must be changed. This appears to be a a common problem. One issue that I discovered is that the old planetary had an Oring in the shaft The replacement parts do not. They must have changed the design so please make sure that food safe grease is used.

replaced the two Bearing slides thanks to your video repair was quite easy

Taking apart the machine is really easy. I was worried the grease would have spilled all over the places, but when the machine is cool, the grease is solid, so no spill. Replace the parts is quite straightforward, and there are plenty of tutorials on line. The only tip is that the grease used by KitchenAid is dark, and it is not easy to see all the small parts when you take the gearbox apart, so pay attention at what you do and at what you throw away... when I got to put it back together I missed a special concave washer which must have been trapped in the grease. Other than that... it has been an easy repair, the mixer is back up and running and I saved a ton on $$$

Found a kitchen aid repair video. Found your site for the part I needed. The connections were not like what the video showed but there were enough connector symbols that I was able to understand where they needed to connect. Marking the connections helped for making the new connections when the new circuit board came.