KG25H0XBK5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
mixer was very noisy when running and made a horrible grinding sound
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hamburg, MN
- Parts Used:
- WPW10170081, WPW10170080, 8212396, WP9709511, WP9709231, W11086780, WP9703445
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gears and bearing failure
inspected and replaced worn components
Was this instruction helpful to you?
Thank you for voting!
Last repairperson broke the top cover of the gearcase ; still need this part .
Easy ; remove belt ( 1 screw ) remove cover , and there is the complete drive . I still need the top plastic cover which is cracked and broken where the bolts go through . Please quote this part .Conradt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FLINT, MI
- Parts Used:
- W11200218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad gears
Easily took apart and replaced gears. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bunny from WAMEGO, KS
- Parts Used:
- W11086780, WP9703680, WP67500-55, W11084660
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Worm gear wore out
Dismantled gear box pulled all gears out and replaced worm gears
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Mentone, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PEORIA, AZ
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Stripped Gear Mixer would not mix
I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EBEN from WEST PALM BCH, FL
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
unit would only operate at high speed
using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
Was this instruction helpful to you?
Thank you for voting!
attachment planetary gears stripped
removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.
Reassembled mixer.
Was this instruction helpful to you?
Thank you for voting!
Planetary Pinion Gear Assembly had dropped down
The repair was easy, I only had to order new gear assembly parts and to replace the associated worn parts (shaft, pin, and gears).
Was this instruction helpful to you?
Thank you for voting!
Bad control switch, striped worm follower gear.
Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCISCO from SAN BENITO, TX
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
REPLACE SPEED CONTROL SWITCH
REPLACE SPPED CONTROL SWITCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Jamestown, ND
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gear teeth worn off worm gear
replace worm gear
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Was this instruction helpful to you?
Thank you for voting!
Worn gear
Remover screws from top. Used snap ring pliers to remove snap ring replaced gear and reassemblied.
Was this instruction helpful to you?
Thank you for voting!