5KSM150PSPPT5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dean from Fairfax, VA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer bowl was slipping off the base when in use
Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Lynden, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Thumb screw
the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Albuquerque, NM
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wire Whip was coming apart
Replaced it with a new part. No installation or repair to maching was necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Belle Fourche, SD
- Parts Used:
- WPW10674618
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the dough hook was chipped
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from San Antonio, TX
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pin fell out of neck
Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashok from Sterling, VA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The worm gear was damaged
I how the video for replacing the worm gear on your website. It help me a lot. I followed step by step instruction display on video. It was great help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Altadena, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Worn out worm (nylon) gear.
Followed up by your précised video, and print copy's which helped me a lot. That's easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from McDonough, GA
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
Beater/Mixer Ran many hours, Rubbed paint off tip
Ordered new paddle beater, rmoved old beater from mach, took new beater from plstc bag, inserted into mixer in appropriate plc, turned on mixer. YES!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from Northport, ME
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Worm gear broken.
Followed directions video on line. good directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Bethlehem, PA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
worn teflon worm gear
it was a kitchen aid dough mixer, had to take the top portion off and replace the assembly with a new one that holds the teflon gear. You can purchace the gear only and it becomes less expensive, but at the time I didn't take the chance cause the greese was there and didn't want to take a chance. Its a simple repair by removing some cotter pins and phillips head screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Seneca, SC
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Mixer jammed, then would not mix, motor ran
Wish that I had known about the video before disassembling. I did not know if it needed a part or was just jammed. It was clear that i needed a worm gear. So I ordered that. It turned out that I needed the Pinion Shaft w/ gear too. So another order. The shipping far exceeded the cost of the parts. NOTE: Clear off as much grease as necessary to be certain that there are no stripped gears anywhere, the order the parts. I took the mixer head off of the stand. I would suggest that you take a bath towel, roll each end towards the center, and place the mixed head so that it is supported on both sides by the towel rolls. NOTE2: Shipping was great 2 days or less. One part arrived on a Saturday. P>S> I do not know the age of this mixer. The age drop down menu should have an UNKNOW option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from South Port, NC
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
mixer stopped working
i followed the instructions in video. Thank you joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Volant, PA
- Parts Used:
- WP240210-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Teeth broke off pinion gear
I watched the video twice and made the repairs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Spring Valley, CA
- Parts Used:
- WPW10191926
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
37 year old screw cap worn, wouldn't hold bowl with heavy dough
Easy removal of old screw cap, but new one didn't just drop in. Had to scrape paint and a little aluminum to make it fit. Finally did, and it works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Ledyard, CT
- Parts Used:
- WP243368
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn spring would not allow atthing mixer attacments
Repair was easy. Remove the seal ring with a flat blade screwdriver and drive out retaining pin. Pry out lower unit using two screwdrivers, one on each side. Once apart, use spring clip pliers to remove snap ring. Pull out shaft and replace. Clean and lubricate as you reassemble in reverse. Google the model number to get detailed instructions.
Was this instruction helpful to you?
Thank you for voting!