7KSM195PSZOA5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lawrence from Craryville, NY
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip brokrn
Just screwed it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Atlanta, GA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken worm gear
Knob fell out of the front of the mixer into the bowl and jammed the beater. This caused the motor to strip the plastic worm gear. Open unit to investigate and found about 4 teeth missing out of the worm gear. Ordered a replacement. Installed the new gear once received in about 30 minutes. Wife is now happy again. Just need to make sure you pack enough gease into the new gear before reassembling the unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from South Port, NC
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
mixer stopped working
i followed the instructions in video. Thank you joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Fairfax, VA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer bowl was slipping off the base when in use
Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Valencia, CA
- Parts Used:
- WP16910
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
The head of my machine was sagging
and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from San Antonio, TX
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pin fell out of neck
Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Albuquerque, NM
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wire Whip was coming apart
Replaced it with a new part. No installation or repair to maching was necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Tracy, MN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic worm gear stripped
The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Spring Valley, CA
- Parts Used:
- WPW10191926
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
37 year old screw cap worn, wouldn't hold bowl with heavy dough
Easy removal of old screw cap, but new one didn't just drop in. Had to scrape paint and a little aluminum to make it fit. Finally did, and it works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from Northport, ME
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Worm gear broken.
Followed directions video on line. good directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Seneca, SC
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Mixer jammed, then would not mix, motor ran
Wish that I had known about the video before disassembling. I did not know if it needed a part or was just jammed. It was clear that i needed a worm gear. So I ordered that. It turned out that I needed the Pinion Shaft w/ gear too. So another order. The shipping far exceeded the cost of the parts. NOTE: Clear off as much grease as necessary to be certain that there are no stripped gears anywhere, the order the parts. I took the mixer head off of the stand. I would suggest that you take a bath towel, roll each end towards the center, and place the mixed head so that it is supported on both sides by the towel rolls. NOTE2: Shipping was great 2 days or less. One part arrived on a Saturday. P>S> I do not know the age of this mixer. The age drop down menu should have an UNKNOW option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert J from Stephenson, MI
- Parts Used:
- WPW10112253, WP9705444, W11082541
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Motor runs, no motion at the business end of the mixer.
Took the mixer down to the gear box. Found the plastic drive gear had a few stripped teeth. Did a search on the internet for the mixer gear. Found a couple of suppliers. Ordered the needed gear, pin and a bearing block just in case it was worn. The bearing block did not need to be replaced. Cleaned the broken off teeth from the gear grease and put the mixer back together. All worked fine when I plugged it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Cincinnati, OH
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Mixer would stop spinning.
I found a video on how to repair mixer that would not turn. Watched video several times and replaced worn worm gear. Getting the old worm gear was the most difficult part of the job. I had to go purchase a pin punch ($5.50) with the correct tool is was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from dahlonega, GA
- Parts Used:
- WPW10112253, W11082541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Worn Worm gear
I took out the worm gear and replaced it with the new one. It is important to have the correct punches that are just under the diameter of the pins.
Was this instruction helpful to you?
Thank you for voting!