KSM150QXDR5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from CUBA, NY
- Parts Used:
- W11557271, WPW10119326, WP9709276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Speed switch wouldn’t stay in off position
Watched a YouTube video to disassemble,from there went smoothly. One small piece of advice,take pictures with your smart phone during the process. Makes remembering easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from CAPE CORAL, FL
- Parts Used:
- W11557271, WPW10119326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
The speed linkage was broken inside the mixer.
Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thanks for having our parts and guiding us with a diagram of the unit. Very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLUMBIA, NJ
- Parts Used:
- WP9705444
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Pin was missing therefore no mixing function
Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom
Run a test and all is good ??
make sure to use a drift pin set
Tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Escondido, CA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic outer casing on tightening screw had broken
This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanislaw from San Antonio, TX
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken wire whip
no instructions necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONG from Elk Grove, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The worm gear was broken
I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from SALINAS, CA
- Parts Used:
- WPW10112253, WP9709280
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Kitchen Aid Mixer won't spin
Order the worm gear part number PS11748374.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk
I would recommend two people if possible.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk
I would recommend two people if possible.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosa from GLOUCESTER, MA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Wasn’t spin any moore
Follow a YouTube video step by step
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from MARIENVILLE, PA
- Parts Used:
- WPW10112253, WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Mixer would slip gears under load, finally would not mix under any load
Rather than duplicate previous repair works, I recommend going to this user site and follow their instructions: http://www.neilcrockett.com/mixer1.htm. Once you have done this repair, taking the unit apart is easier to perform this tasks. Order replacement Grease "Benalene 930-2" in the 3.3 oz container and be sure to use the full container to lather all around all the gear components so grease will be available to units for years to come due to heat build up under load. Too, the 3.5 oz container is made for one unit repair job and is available through Amazon. This grease is available on larger quantities if needed / desired. I did order both, a Worm Gear and the Worm Gear and Bracket as I wasn't sure of my mechanical ability to make this repair until I got inside the unit but the worm gear is easily replaced once you clean out all the old grease. The worm gear is a neoprene type gear with all other gears being metal. I assume neoprene is used as sacrificial to save other gears from breaking under loads and years of use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reid from MONTICELLO, MN
- Parts Used:
- WPW10325124, WPW10119326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Speed control not working properly
Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from SANTA FE, NM
- Parts Used:
- WP243368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken beater shaft
Used the diagram on the website and a video
Totally worked!
Totally worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from AURORA, CO
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bowel would come out of screwcap when making dough for pasta
The repair was easy only requiring a phillips head screw driver to remove the old screw cap. The new screw cap fit snuggly and required a little downward pressure from my hand to seat it. Then I simply tightened the screws. Good as new for this 30+ year old mixer. My wife loves this mixer that was given to her by her Aunt. Glad we could keep it going.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from JACKSON, TN
- Parts Used:
- WP9704329
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old wire whip was broken
Just put on the new whip...exactly like old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from FAIRFIELD, CT
- Parts Used:
- WPW10191926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old screw cap wore out and would not hold bowl when mixing heavy batters.
Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mrs Brenda from LYNNWOOD, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screw cracked on the front of the mixer
Skewer the screw in with my fingers,
Was this instruction helpful to you?
Thank you for voting!