5KSM125ELR5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Columbus, OH
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pin was missing on mixer allowing head to move.
Inserted new pin and tightened set screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from St Louis, MO
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic boke on the old thumb screw
unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wewahitchka, FL
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
mixer would not turn
removed the screws holding the mixer housing and then removed the worn worm gear by removing the roll pin holding it on the shaft. Replaced the worm gear and inserted the pin that hole it in place. Replaced some of the gear grease and reassembled mixer. Went very easily. No problems at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SACRAMENTO, CA
- Parts Used:
- W11324096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Mixer bowl that came with the 5 quart mixer would not lock on the base
New mixer bowl locks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EUGENIO from MIAMI, FL
- Parts Used:
- W11192794
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
spent Pevel Pinion Center Gear
remove the back cover part # 36, remove the top cover part # 1 (by removing the chrome ring parate # 28, the mobile disk part # 25 and six screws part # 24). This done, remove the system parat # 38 to release the Pevel Pinion Center Gear part # 15 and remove the damaged part and put the new part. The install the removed parts in reverse order as they withdrew.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLUMBIA, NJ
- Parts Used:
- WP9705444
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Pin was missing therefore no mixing function
Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom
Run a test and all is good ??
make sure to use a drift pin set
Tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanislaw from San Antonio, TX
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken wire whip
no instructions necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Escondido, CA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic outer casing on tightening screw had broken
This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Sherwood, OR
- Parts Used:
- W11192794
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Attachments would not work, spindle turned erratically, with no power
Punched out the roll pin to remove eccentric from spindle, undid 5 screws (after removing trim ring), and removed 4 screws to undo the motor housing. Make sure to keep the one screw with a lock washer in the BACK of the housing. Undid the screw on top to remove the back of the motor housing to take out the strain relief grommet, prior to removing the motor housing. Scraped the excess grease into a tub to re-use. Pulled out the shaft, and lifted out the old (stripped) gear and plopped the new one in. Make sure to mark match points for parts, and put the pins back in in the right order. You have to put the 5 screws back in before sliding the trim ring on, and putting the roll pin back. make sure all gears mesh and test before snugging the motor housing screws. Be sure to orient the strain relief grommet securely, and be careful of the filter plates in the back of the housing (they're brittle). putting the grease back is like frosting a cake. Save a little for the planetary ass'y.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherriel from TERREBONNE, OR
- Parts Used:
- WPW10672617, WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Mixer stop rotating
Replace went good used the online video, my husband doesn't usually use any help but said the video helped him. Now my mixer works perfect. Also the price and shipping time was awesome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from CAPE CORAL, FL
- Parts Used:
- W11557271, WPW10119326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
The speed linkage was broken inside the mixer.
Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thanks for having our parts and guiding us with a diagram of the unit. Very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONG from Elk Grove, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The worm gear was broken
I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mrs Brenda from LYNNWOOD, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screw cracked on the front of the mixer
Skewer the screw in with my fingers,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosa from GLOUCESTER, MA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Wasn’t spin any moore
Follow a YouTube video step by step
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SUQUAMISH, WA
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Replaced worn out gear
Fairly easy if you have done it once before.
Was this instruction helpful to you?
Thank you for voting!