KV25G0XMC4 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mixer blade did not turn, striped gears.
Replaced the worm gears. Original were ground down as if they were not seated correctly. Ordered the parts and swapped them out. I do not own a retaining clip removal tool. This was the most difficult, trying to open the clip using 2 needle nose pliers. It made the repair time longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Greenfield, IN
- Parts Used:
- W11086780
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
broken cog on gear
Researched the internet for a diagram of the mixer and used that to take it apart, clean everything, then install the new gear and new grease. Works great so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Worth, IL
- Parts Used:
- WP9709231
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
gear noise whining
Took the mixer apart many times. Grease all over the place. put new gears in still noisy. The worm gear must have been cut wrong. The noise still there. The part select sent out a new worm gear. I did not put it in yet. I put the old worm gear in and the noise stopped even though it shows wear. Have not decided whether I will put it in yet.I would also like to add that the people that I talked to at the this site were very very helpful and great just great---------
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mrs Brenda from LYNNWOOD, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screw cracked on the front of the mixer
Skewer the screw in with my fingers,
Was this instruction helpful to you?
Thank you for voting!
Teeth in planetary stripped where shaft seated
Removed cover, removed retaining clip from shaft. Removed gear, removed shaft pin. Removed shaft. Installed new planetary and installed pin, gear, retaining clip. Installed covers. Tested Sat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from SAINT LOUIS, MO
- Parts Used:
- WP9708649
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
needed to replace rubber foot on mixer
The insertion part of the foot was tapered to fit in the hole in the mixer. Simple pressure was not the answer. So I used a small key, placed it on the bottom of the foot, after applying a little vegetable oil on the foot, and tapped it into place. Worked well.Joe
Was this instruction helpful to you?
Thank you for voting!
mixer was very noisy when running and made a horrible grinding sound
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.
Was this instruction helpful to you?
Thank you for voting!
Broken thrust bearing kit caused damage to the worn gear
Disassambled the gear-train.Removed all broken pieces and grease from gear case. Cleaned gear case and all parts. Reassembled gear-train with new parts and packed all with suitable quantity of new grease. Test run with variable speeds assuming working smoothly.
Was this instruction helpful to you?
Thank you for voting!
Worm gear had stripped so changed out several gears and parts
Opened the gear housing and removed all gears. Cleaned out all grease. Biggest issue was getting the retaining ring; very tight. Gears were difficult to pull easily. In replacing gears they did not sit easily and took a little rubber hammer to re position worm and upper gear. Be sure to have the right grease for food devices and don’t under grease. And have patience of which I have a short supply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FLINT, MI
- Parts Used:
- W11200218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad gears
Easily took apart and replaced gears. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Mentone, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bunny from WAMEGO, KS
- Parts Used:
- W11086780, WP9703680, WP67500-55, W11084660
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Worm gear wore out
Dismantled gear box pulled all gears out and replaced worm gears
Was this instruction helpful to you?
Thank you for voting!
Bad control switch, striped worm follower gear.
Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CEDAR CREEK, TX
- Parts Used:
- 8212396
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken gear case.
Remove and replace gear case. Apply food grade grease secure with screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EBEN from WEST PALM BCH, FL
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
unit would only operate at high speed
using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
Was this instruction helpful to you?
Thank you for voting!