KSM150FBAQ5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from WESTERVILLE, OH
- Parts Used:
- W11545825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Damaged insulation on the cord
Removed back cover, disconnected the 2 push-on connectors, removed ground wire screw. Reversed the process to install new cord.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ana from PRT JEFFERSON, NY
- Parts Used:
- WPW10674618, WP243368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stuck agitator shaft and dough hook
I had a sourdough batch get into the space where dough hook attaches and it got so stuck that nothing - not hot water baths, not pliers and screwdrivers got the dough hook released. I had to open up the mixer following partselect you tube instructions and replacing the parts. What was confusing to me at first is that my 45 year old mixer had an extra screw on top of the shaft that no longer is there for newer models. It took me longer than I am willing to admit to figure that the extra screw is not the result of me skimming the instructions - the original shaft and dough hook went to a friend who broke it attempting to disengage the two parts (the dough turned out to be a very strong form of glue!). The piece is working like new. I preferred the agitator shaft with a spring to hold the end piece tighter, but the new set up without a spring works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from HUNTINGTON, IN
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn Worm gear. Mixer made a clunking noise and wouldn't turn.
Followed your instructions from the internet and it was a simple fix. Mixer works great again. Thank You ..you made it easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from CISCO, GA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worm gear worn out
I watched a short video on replacing the worm gear, although I did not know what the problem was until I watched the video. after the video ended I took the mixer apart and found the problem located a parts number an placed my order. got the part in one week put in the new part in about 20 minutes and it work like new. and the price was very reasonable
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from ELIZABETH, WV
- Parts Used:
- W11545825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
short in the wiring had blown the ground plug out,,,contact with a mounting screw head
had to replace the outlet strip and relocate the mounting screw,,,,wiring cord to the mixer was super correct and had to simply follow basic wiring (black to black,,,silver to silver,,,green to ground) ,,, the cord came with the correct mounting bushing already on the cord. Thx a bunch!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from HAMPTON, NH
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My stand mixer stopped mixing!
I watched a YouTube video all the way through, then watched each segment and followed along with the video. It was messier than the professional repair guy, but it worked out fine. This is not a difficult repair when you can watch a video and follow along. It saved me about $130.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from SALADO, TX
- Parts Used:
- WPW10323373, WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Worm gear was worn out .
I watched the university of YouTube videos, and followed their instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachael from SEATTLE, WA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Worm gear was stripped and needed to be replaced
I am not handy, but was able to follow this YouTube video and do this repair easily and successfully: https://www.youtube.com/watch?v=1QsgPIL9FpA
I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!
I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from OWASSO, OK
- Parts Used:
- W11192794, WP67500-55, 4160474
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Mixer was making a loud noise and the attachment port was not working
Watched a couple of youtube videos and it was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from ELY, MN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No rotation on mixer
You tube has great instructions! I would suggest when you buy a part to let customer know that they need a food grade gear grease ordered to complete the reinstall of all gears and body parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from MILWAUKEE, WI
- Parts Used:
- W11192794
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
EXTRUDER GEARS GROUND DOWN AND STOPPED WORKING
Dismantled the mixer, took photos, and re-assembled unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CEDAR CITY, UT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic worm gear gave way (as designed) when the grain mill over-worked it.
I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from GRAPEVINE, TX
- Parts Used:
- W11192794
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Attachment hub stopped spinning
Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curt from SHELBY, MI
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Teeth on the gear were worn off.
Took each area apart. Replaced the gear and reassembled it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from ELKHART, IN
- Parts Used:
- WPW10325124, WPW10119326
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
SPEED WENT CRAZY, VERY VERY FAST. NO CONTROL AT ALL EXCEPT OFF
INSTALLED PHASE CONTROL BOARD AND SPEED CONTROL PLATE, BOTH AT SAME TIME
Your DYI video was helpful, especially holding the spring with a cloth. Also good for fine tuning to get the speed exact
Your DYI video was helpful, especially holding the spring with a cloth. Also good for fine tuning to get the speed exact
Was this instruction helpful to you?
Thank you for voting!