5KSM195PSAHI0 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Erwin from Northport, ME
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Worm gear broken.
Followed directions video on line. good directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franciska from Carrollton, TX
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bent wisk
replace wisk order process very efficient and delivery prompt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Bethlehem, PA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
worn teflon worm gear
it was a kitchen aid dough mixer, had to take the top portion off and replace the assembly with a new one that holds the teflon gear. You can purchace the gear only and it becomes less expensive, but at the time I didn't take the chance cause the greese was there and didn't want to take a chance. Its a simple repair by removing some cotter pins and phillips head screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrew from bridgeville, PA
- Parts Used:
- WPW10380496, W11656718
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
would not run
I just put in the new brushes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Valencia, CA
- Parts Used:
- WP16910
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
The head of my machine was sagging
and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Fairfax, VA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer bowl was slipping off the base when in use
Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Naperville, IL
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My wife was complaining of a loud grinding noise.
I replaced the brushes. I didn't realize that I've put one of them wrong. Reminder for next time the brushes have to touch the rotor of the motor. It took me a little bit to understand but the brushes can go in and not touch the rotor. It works very quietly now. Thank you PartSelect for your infos and knowledge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Takahiro from Arlington, MA
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Food mixer suddenly stopped without burnning smell
Just change the motor brush. That's it! It work well now. Thank you, Partselect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Tracy, MN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic worm gear stripped
The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Craryville, NY
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip brokrn
Just screwed it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Atlanta, GA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken worm gear
Knob fell out of the front of the mixer into the bowl and jammed the beater. This caused the motor to strip the plastic worm gear. Open unit to investigate and found about 4 teeth missing out of the worm gear. Ordered a replacement. Installed the new gear once received in about 30 minutes. Wife is now happy again. Just need to make sure you pack enough gease into the new gear before reassembling the unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Albuquerque, NM
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wire Whip was coming apart
Replaced it with a new part. No installation or repair to maching was necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from San Antonio, TX
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pin fell out of neck
Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Scottsburg, IN
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Brush's Wore
Change brush's
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Rockdale, IL
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
machine not running-broken worm gear?
After I dropped a part of the shield into my mixer the motor screamed and I unplugged the mixer. I found out I had a broken worm gear. I then order the part and per the helpful video I did the repair and I also changed the brushes my mixer is up and running waiting for the holiday baking season thanks to Part select.com Very easy Instructions to follow I am very happy with the results. Thanks Barbara
Was this instruction helpful to you?
Thank you for voting!