9KSM160FGAWH5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ana from PRT JEFFERSON, NY
- Parts Used:
- WPW10674618, WP243368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stuck agitator shaft and dough hook
I had a sourdough batch get into the space where dough hook attaches and it got so stuck that nothing - not hot water baths, not pliers and screwdrivers got the dough hook released. I had to open up the mixer following partselect you tube instructions and replacing the parts. What was confusing to me at first is that my 45 year old mixer had an extra screw on top of the shaft that no longer is there for newer models. It took me longer than I am willing to admit to figure that the extra screw is not the result of me skimming the instructions - the original shaft and dough hook went to a friend who broke it attempting to disengage the two parts (the dough turned out to be a very strong form of glue!). The piece is working like new. I preferred the agitator shaft with a spring to hold the end piece tighter, but the new set up without a spring works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from JACKSONVILLE, NC
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The mixer broke the worm gear(the only plastic gear inside the mixer) and needed replaced.
I took apart the mixer housing and removed all the screws. The most difficult part was the two pins that needed to be removed with a metal punch. They were in fairly tight. The mixer came apart pretty easily and it was obvious which part needed to be replaced as it was broken and missing teeth. After replacing the gear and applying new grease for smooth operation, I simply put it back together and it has worked like new ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from MILWAUKEE, WI
- Parts Used:
- W11192794
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
EXTRUDER GEARS GROUND DOWN AND STOPPED WORKING
Dismantled the mixer, took photos, and re-assembled unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Locust Grove, VA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
cap screw was worn out and would not hold the bowl
Removed three screws and lifted out old part. replaced with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from OSSINEKE, MI
- Parts Used:
- WPW10325124
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Control stuck in high gear.
With the mixer being over 30 years old we believed it has going to have to be replaced. However, my husband jumped on uTube and looked at reviews for the problem. Motor was only running on high speed. Reviews said to replace the phase control board. Repair was very quick by just taking off the cover. Removing the old board and connecting the new. Mixer is working awesome once again. In such a disposable society it is great to be able to fix vs trash. Happy Baker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from LEXINGTON, SC
- Parts Used:
- WPW10672617
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The white enamel coating was breaking off the mixer beater. There was a scrapimg noise when the beater was in motion.
I simply inserted the new beater into the mixer to see if it scraped the sides of the bowl. It fit perfectly and didn't scrape the bowl like the old one did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from CHARLESTON, SC
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The threads on the plate that holds the bowl had stripped and the bowl flew off when mixing
Removed old plate, screwed in new plate and works like new! Was so happy I wouldn’t have to replace my 30 year old mixer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from JACKSONVILLE, FL
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Mixer went to high speed immediately on starting
Simple fix actually. UNPLUG mixer and remove the one screw on top that holds on the back. The Phase control board sits under and behind the paper insulator and "switch" assy. Remove the 4 wires with a pair of needle nose pliers, the one screw holding it to the back of the mixer and install the new one in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from COXS CREEK, KY
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bowl lock wouldn't hold when mixing bread
Repair is very straight forward. Remove the existing plate by removing the three phillip head screws. Use a regular screwdriver or knife to pop the plate off. (I cleaned the area while I was there but probably not necessary) Position the new plate with the screw holes lined up. Press down to pop the plate into position. Install original screws and tighten. You're done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GALO from DECATUR, GA
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer operarates at high speed only.
Removed old one and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SAINT PAUL, MN
- Parts Used:
- WPW10119326
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The mixer was given to my wife. Sometimes it would work or not.
When I took the back cover off I found two parts that "could" be the problem. The speed control plate was cracked which explained the spotty working. I ordered both parts and installed them very easily. The parts fit perfectly and resulted in the mixer working perfectly. I can't say enough about the excellent parts. They were perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from St. James, MN
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip came apart
Really no help from Kitchen Aid sources; but phone call to PartSelect solved the problem. Kitchen Aid repair line didn't even know the part #! Thanks to Part/Select, Christmas cookies are being made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lynchburg, VA
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip got bent and had to be replaced
just inserted the new wire whip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Auburn, ME
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn gear
dissassembled mixer and replaced gear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- H. from Hollister, CA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Damaged the worm gear in our 300w mixer.
After stalling the mixer while mixing dough I found that the motor still functioned but the blade didn't move. I basically took the mixer into my shop along with a digital camera to record any complicated disassembly procedure I might have to deal with for reassembly and proceeded to disassemble the mixer. Once apart, I cleaned the mixer parts, removed the broken worm gear and bracket, and got online for someone that carried the replacement piece. PartSelect sent the replacement within 3 days and now it works great again.
Was this instruction helpful to you?
Thank you for voting!