5KSM150PSZBM5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from Cincinnati, OH
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Mixer would stop spinning.
I found a video on how to repair mixer that would not turn. Watched video several times and replaced worn worm gear. Getting the old worm gear was the most difficult part of the job. I had to go purchase a pin punch ($5.50) with the correct tool is was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amalia from Granville, OH
- Parts Used:
- WPW10112253, WP240210-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
One of the parts broke 3 teeth and did not work anymore.
Unscrew and dismounted the mixer, gather all pieces and screws, cleaned and washed every part, took away the old grease and replaced it with a new one, also looked carefully for the lost teeth and found them, Put grease in every part, put back and screwed all the pieces of the mixer, then tried the mixer which worked really well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgianne from Castro Valley, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
My kitchenaid stopped moving
My husband looked at youtube to figure out what the issue was. He saw a video that identified that the likely problem was the worm gear. My husband took the kitchenaid applicance apart, as he saw in the video. We ordered the part, it took less than a week to arrive. He rewatched the video that demonstrated how to put the kitchenaid mixer back together. It's a bit messy due to all the packing grease, but a pair of nitrile gloves, paper towels, and an old rag help. We put a garbage bag over the appliance after it was taken apart to protect it from any dust and my curious cat. We let the kitchenaid cycle for about a minute to make sure the gear was greased. I haven't used it to make bread yet, but I'll do that soon. Thanks for supplying the part that saved us at least one hundred dollars and TRY to get a person who will repair small appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from LIGNITE, ND
- Parts Used:
- WP9709194, WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Beater was peeling and chipped; thumb screw was worn & loose to the point it would fall out
It only involves reinserting the beater . And the thumb-screw was falling out so I cleaned the area and replaced the thumb screw. Very simple and easily done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Holland, MI
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part worn out, wouldn't hold mixing bowl
unscrewed old part, put in new part.New part much better design than old one. Works great. Your service is great. Had the part in a 2-3 days. Awesome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Blairsville, GA
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bent wires in a wire whip
I ordered a new wire whip and attached it just like it was the original. WALLA!!! Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Glen Ellyn, IL
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The screw cap no longer held the bowl in place.
This is the easiest repair ever! I removed the 3 screws, cleaned around the area with a sponge and kitchen cleaner and put on the new cap. The screws went back in easily and voila ! Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marjorie from juda, WI
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
head of screw was broken in half
I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Aitkin, MN
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screw cap or retainer wore out and wouldn't hold the bowl tight
Removed the old screw cap and installed the new one-only has 3 screw to remove and re install. VERY easy. Fits perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tolland, CT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sticky back disc on Orbital sander came apart (from old age )
remove 3 screws ,remove old sanding disc replace with new installl screws
Was this instruction helpful to you?
Thank you for voting!
Replaced main gears
1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franciska from Carrollton, TX
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bent wisk
replace wisk order process very efficient and delivery prompt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Jackson, WI
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Coating on beater wore off
Simply replaced the beater.Ordering part was simple and delivery was quick. I was back at baking in no time! Great service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernet from Birmingham, AL
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No repair I purchased a part.
The part fit great! PS. I may need to buy a gasket to go around my refrigerator door. I have an Amana Model #THI1853W, Serial No. 9502301998. Do you have instructions on how to install this gasket?
Was this instruction helpful to you?
Thank you for voting!