5KSM185PSBKG5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Randall from Ledyard, CT
- Parts Used:
- WP243368
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn spring would not allow atthing mixer attacments
Repair was easy. Remove the seal ring with a flat blade screwdriver and drive out retaining pin. Pry out lower unit using two screwdrivers, one on each side. Once apart, use spring clip pliers to remove snap ring. Pull out shaft and replace. Clean and lubricate as you reassemble in reverse. Google the model number to get detailed instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from El Paso, TX
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No rotation
I was very happy with the customer services department and the support I received in identifying the part I needed for the repair. I received an email confirming my order with all details. I do wish you had a more cost effective shipping alternative, like Priority mail.
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.
Thank you
Ron Ashby
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.
Thank you
Ron Ashby
Was this instruction helpful to you?
Thank you for voting!
Replaced main gears
1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from San Antonio, TX
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pin fell out of neck
Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Holland, MI
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part worn out, wouldn't hold mixing bowl
unscrewed old part, put in new part.New part much better design than old one. Works great. Your service is great. Had the part in a 2-3 days. Awesome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Glen Ellyn, IL
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The screw cap no longer held the bowl in place.
This is the easiest repair ever! I removed the 3 screws, cleaned around the area with a sponge and kitchen cleaner and put on the new cap. The screws went back in easily and voila ! Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Aitkin, MN
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screw cap or retainer wore out and wouldn't hold the bowl tight
Removed the old screw cap and installed the new one-only has 3 screw to remove and re install. VERY easy. Fits perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tolland, CT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sticky back disc on Orbital sander came apart (from old age )
remove 3 screws ,remove old sanding disc replace with new installl screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Valencia, CA
- Parts Used:
- WP16910
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
The head of my machine was sagging
and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Tracy, MN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic worm gear stripped
The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Manheim, PA
- Parts Used:
- WP9709707
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Lost a rubber foot on my Kitchen Aid mixer. The remaining feet we're hard and mushroomed. I decided to replace all 5. That was the correct decision.
I griped each foot with a pliers and twisted it out of its setting. I then set a new foot in place and hammered it into place with a small hammer. The feet fit snugly and did not need to be glued. Job was easy and mixer sits like new. I was glad I spent the money to replace all of the feet at once.
Was this instruction helpful to you?
Thank you for voting!