9KSM150PSER5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dustin from JACKSONVILLE, NC
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The mixer broke the worm gear(the only plastic gear inside the mixer) and needed replaced.
I took apart the mixer housing and removed all the screws. The most difficult part was the two pins that needed to be removed with a metal punch. They were in fairly tight. The mixer came apart pretty easily and it was obvious which part needed to be replaced as it was broken and missing teeth. After replacing the gear and applying new grease for smooth operation, I simply put it back together and it has worked like new ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sylvia from HILTON, NY
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The original screw cap would not hold the mixer bowl in place anymore.
The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from CISCO, GA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worm gear worn out
I watched a short video on replacing the worm gear, although I did not know what the problem was until I watched the video. after the video ended I took the mixer apart and found the problem located a parts number an placed my order. got the part in one week put in the new part in about 20 minutes and it work like new. and the price was very reasonable
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from HUNTINGTON, IN
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn Worm gear. Mixer made a clunking noise and wouldn't turn.
Followed your instructions from the internet and it was a simple fix. Mixer works great again. Thank You ..you made it easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from CHARLESTON, SC
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The threads on the plate that holds the bowl had stripped and the bowl flew off when mixing
Removed old plate, screwed in new plate and works like new! Was so happy I wouldn’t have to replace my 30 year old mixer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from OSSINEKE, MI
- Parts Used:
- WPW10325124
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Control stuck in high gear.
With the mixer being over 30 years old we believed it has going to have to be replaced. However, my husband jumped on uTube and looked at reviews for the problem. Motor was only running on high speed. Reviews said to replace the phase control board. Repair was very quick by just taking off the cover. Removing the old board and connecting the new. Mixer is working awesome once again. In such a disposable society it is great to be able to fix vs trash. Happy Baker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Locust Grove, VA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
cap screw was worn out and would not hold the bowl
Removed three screws and lifted out old part. replaced with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GALO from DECATUR, GA
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer operarates at high speed only.
Removed old one and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from LEXINGTON, SC
- Parts Used:
- WPW10672617
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The white enamel coating was breaking off the mixer beater. There was a scrapimg noise when the beater was in motion.
I simply inserted the new beater into the mixer to see if it scraped the sides of the bowl. It fit perfectly and didn't scrape the bowl like the old one did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from COXS CREEK, KY
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bowl lock wouldn't hold when mixing bread
Repair is very straight forward. Remove the existing plate by removing the three phillip head screws. Use a regular screwdriver or knife to pop the plate off. (I cleaned the area while I was there but probably not necessary) Position the new plate with the screw holes lined up. Press down to pop the plate into position. Install original screws and tighten. You're done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from St. James, MN
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip came apart
Really no help from Kitchen Aid sources; but phone call to PartSelect solved the problem. Kitchen Aid repair line didn't even know the part #! Thanks to Part/Select, Christmas cookies are being made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lynchburg, VA
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip got bent and had to be replaced
just inserted the new wire whip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SAINT PAUL, MN
- Parts Used:
- WPW10119326
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The mixer was given to my wife. Sometimes it would work or not.
When I took the back cover off I found two parts that "could" be the problem. The speed control plate was cracked which explained the spotty working. I ordered both parts and installed them very easily. The parts fit perfectly and resulted in the mixer working perfectly. I can't say enough about the excellent parts. They were perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Auburn, ME
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn gear
dissassembled mixer and replaced gear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- H. from Hollister, CA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Damaged the worm gear in our 300w mixer.
After stalling the mixer while mixing dough I found that the motor still functioned but the blade didn't move. I basically took the mixer into my shop along with a digital camera to record any complicated disassembly procedure I might have to deal with for reassembly and proceeded to disassemble the mixer. Once apart, I cleaned the mixer parts, removed the broken worm gear and bracket, and got online for someone that carried the replacement piece. PartSelect sent the replacement within 3 days and now it works great again.
Was this instruction helpful to you?
Thank you for voting!