3KSM150PSTIC5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joan from Nokomis, FL
- Parts Used:
- WP240309-2
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
gear was stripped , head wouldn;t turn
We followed the you tube instructional video. It was excellent with good advice that kept us out of trouble. My mixer works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Post Falls, ID
- Parts Used:
- WP9709707
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The 5 feet on my Kitchen Aide, had worn out
Took the old feet (5) off and put new on the Kitchen Aide, looks great. Stands high and your assistance on the phone, was so appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Green River, WY
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Moter would run, but nothing would turn
first removed the dress ring by tapping it very gently.then drive the pin out that holds the beater plate on, now wiggle it off, then you can see the screws that hold the gear reducer on. remove them. take that off and you will see the housing that hold the worm gear. remove the 3 screws that hold it down . Now you will have to drive the drift pin out that holds the worm gear in place, slide the shaft out then remove gear. reverse order to assemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from CAMPO, CA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
1960s Kitchenaid K45 Mixer Screw Cap Stripped
My early '60's Kitchenaid K45 mixer screw cap/base plate would no longer hold the bowl, so I looked for another. This item, though not an exact replica of the original, fit and works great. The design is better by being more stout than the original. Pretty straightforward installation: remove three screws, take out old base plate, install new plate and screw down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Cupertino, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Stripped gear when I tried to make Pizza Dough
Very messy as there is lots of heavy grease inside the mixer and you have to fish out the blown gear parts. I vary glad I took shop class in High school as it preped me for the job. The machanical drawing you provide were very useful but you should mention the grease.
Mixer works just like new. and I got the parts in two days with standard shipping. Pizza on Thursday and fixed by Saturday
Mixer works just like new. and I got the parts in two days with standard shipping. Pizza on Thursday and fixed by Saturday
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Rochester, NY
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire broke
total replacement
works beautifully
works beautifully
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from eudora, AR
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very simple could not been a easer job thank for partsSelect.
all that were required, were you take off old beater an replace new.simple push up old part an replace new. as you do after usage of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Pigeon, MI
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Worm gear was missing teeth
Took the mixer apart and cleaned the grease so off I could see the pins. Wasn't a hard fix only thing is make sure to clean the grease off so you can see what your doing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- A. W. from Rogers, AR
- Parts Used:
- WP240309-2
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The Kitchenaid heavy duty mixer's motor would run but the mixer head would not turn.
Obviously the problem was in the gear box of the mixer. I disassembled the gear box by removing the four large screws holding the base then the four screws at the rear and center of the mixer. Then I removed the thin metal ring covering the five screws around the front of the housing by gently prying up with a small screwdriver. The five screws beneth the ring have to be removed with a small blade screwdriver turning them a round at a time in sequence until they are free. Gently pry the two housings apart with a screwdriver and lift our the lower half with the plantary gears. I found the drive gear was stripped. I went to PartSelect on the web, eaisly found the exploded view of the mixer's gear box and ordered the gear I needed. The gear is part of an assembly attached to the mixer housing with three screws. Work around the lubricant in the housing. Within four days I received the new gear, installed it by reversing the above procedures and the mixer is working again. The total cost was $34.85. Not a bad investment considering the mixer cost over $400 and would have been trashed for want of one part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Marshfield, WI
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The coating was chipping off of the original Flat Beater
All I had to do was insert the new beater. Wonderful timing, was just going to start some holiday baking. will definetly use your website again. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- .JENNIFER from STAR, ID
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
powder coating came off mixer paddle.
put new paddle on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CARLISLE, PA
- Parts Used:
- WP9709707
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing pedestal foot
Turned the mixer on its side and slid the part into the bottom of the base.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GREENWOOD, IN
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
planetary gear would not turn; discovered worm gear was broken upon dis-assembly of mixer
Followed step-by-step video instructions for dis-assembly/reassembly found at ereplacementparts.com. All went well except when driving out the pin that holds the worm gear in the tower. The video wasn't exactly clear enough about what position the pin should be in when driving it out and I inadvertently drove the pin out so that it was trapped inside the tower assembly. Result? I had to bend the pin to get it out, causing an extra expenditure and wait time to order a new pin. So, lesson learned: be sure the pin is horizontal to the tower and not perpendicular to when driving the pin out. Also, I found that having the mixer apart was a good time to replace the grease in the housing. I don't think it would be required to replace the grease at this time but I was worried that pieces of the old worm gear could remain in the grease and possible get jammed in the gears after repairs were completed. Be sure to get a "food grade" grease not grease from your local auto parts store! The table knife was the best tool to use to remove the grease and to smear the grease all over the internal gears when replacing it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennife from Lancaster, PA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Worm gear broken
I called my fiancée.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from Ferndale, CA
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new flat beater
Just replaced the beater.
Was this instruction helpful to you?
Thank you for voting!