KSM192XDER0 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Randall from Ledyard, CT
- Parts Used:
- WP243368
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn spring would not allow atthing mixer attacments
Repair was easy. Remove the seal ring with a flat blade screwdriver and drive out retaining pin. Pry out lower unit using two screwdrivers, one on each side. Once apart, use spring clip pliers to remove snap ring. Pull out shaft and replace. Clean and lubricate as you reassemble in reverse. Google the model number to get detailed instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Stillwater, MN
- Parts Used:
- WPW10325124
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable), Wrench set
Fast speed on every setting. No control of speeds.
I removed the cover off the back of the mixer. Carefully remove the cardboard gasket around the outside edge. Unlock the nuts that hold the two adjusting screws. Count the turns to remove each screw in order to keep the right adjustment. Pull the plate away enough to remove the control board. There is one long and one short wire that gets plugged into each side of the plate. Watch the location of each wire to make the right connection. Reattach the screws to the proper position. Then install the gasket and rear cover. Check for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roland from Newport, OH
- Parts Used:
- WPW10191926
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
kitchen aid mixer wouldn't hold the bowl for kneading or mixing cookie dough
Unscrewed 3 Philips screws. Pried out the old screw cap. It had been there for 25 years and had flour, egg, etc. build up over the years. Did use a needle nose plier to lift it out. Put in the new one. Needed a rubber mallet to snug it down. Design has changed slightly over the years. Put the 3 screws back in and as they say in England, "you have an uncle named Bob."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Spring Valley, CA
- Parts Used:
- WPW10191926
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
37 year old screw cap worn, wouldn't hold bowl with heavy dough
Easy removal of old screw cap, but new one didn't just drop in. Had to scrape paint and a little aluminum to make it fit. Finally did, and it works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from las Vegas, NV
- Parts Used:
- WPW10380496
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Brushes go in only one way & not same each
Took it to repair shop
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from South Port, NC
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
mixer stopped working
i followed the instructions in video. Thank you joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Volant, PA
- Parts Used:
- WP240210-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Teeth broke off pinion gear
I watched the video twice and made the repairs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashley from Dayton, OH
- Parts Used:
- WPW10380496, 4162546
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Nothing would happen when we turned it on...
The brushes on the inside of the motor were destroyed. We thought that it would be easier to just replace the brush holder and the brushes, however, the brushes were easy! and QUICK! The brush holders...not so much. We had lots of problems getting the brush holders into place because of a metal piece that had to fit perfectly on top of the brush holder. It made it easier when I held the mixer upside down (we dissembled it) and my husband did his magic on fixing the brush holders. Pray that you won't need to replace the brush holders because it was NO FUN...but the brushes were QUICK AND EASY :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Naperville, IL
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My wife was complaining of a loud grinding noise.
I replaced the brushes. I didn't realize that I've put one of them wrong. Reminder for next time the brushes have to touch the rotor of the motor. It took me a little bit to understand but the brushes can go in and not touch the rotor. It works very quietly now. Thank you PartSelect for your infos and knowledge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashok from Sterling, VA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The worm gear was damaged
I how the video for replacing the worm gear on your website. It help me a lot. I followed step by step instruction display on video. It was great help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from San Antonio, TX
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pin fell out of neck
Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Albuquerque, NM
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wire Whip was coming apart
Replaced it with a new part. No installation or repair to maching was necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from El Paso, TX
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No rotation
I was very happy with the customer services department and the support I received in identifying the part I needed for the repair. I received an email confirming my order with all details. I do wish you had a more cost effective shipping alternative, like Priority mail.
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.
Thank you
Ron Ashby
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.
Thank you
Ron Ashby
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Craryville, NY
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip brokrn
Just screwed it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Tracy, MN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic worm gear stripped
The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.
Was this instruction helpful to you?
Thank you for voting!