5KSM195PSABE5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Norfolk, VA
- Parts Used:
- WPW10119326
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
mixer would not turn on
removed one screw from back cover, loosened two screws holding speed control plate, removed one wire at a time from old unit to new, screwed two top screws back on mixer,plug mixer back in, adjust speed control screws until I reached correct speed, put back cover back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvaro from Brighton, CO
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worm gear was bad
Order part through parts select. it only took 3 days to receive part. The mixer was very easy to take apart and to replace the gear. it was back together in about 20 min. The video from kitchen aid to repair the unit is awsome. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from El Paso, TX
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No rotation
I was very happy with the customer services department and the support I received in identifying the part I needed for the repair. I received an email confirming my order with all details. I do wish you had a more cost effective shipping alternative, like Priority mail.
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.
Thank you
Ron Ashby
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.
Thank you
Ron Ashby
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Ledyard, CT
- Parts Used:
- WP243368
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn spring would not allow atthing mixer attacments
Repair was easy. Remove the seal ring with a flat blade screwdriver and drive out retaining pin. Pry out lower unit using two screwdrivers, one on each side. Once apart, use spring clip pliers to remove snap ring. Pull out shaft and replace. Clean and lubricate as you reassemble in reverse. Google the model number to get detailed instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from South Port, NC
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
mixer stopped working
i followed the instructions in video. Thank you joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Seneca, SC
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Mixer jammed, then would not mix, motor ran
Wish that I had known about the video before disassembling. I did not know if it needed a part or was just jammed. It was clear that i needed a worm gear. So I ordered that. It turned out that I needed the Pinion Shaft w/ gear too. So another order. The shipping far exceeded the cost of the parts. NOTE: Clear off as much grease as necessary to be certain that there are no stripped gears anywhere, the order the parts. I took the mixer head off of the stand. I would suggest that you take a bath towel, roll each end towards the center, and place the mixed head so that it is supported on both sides by the towel rolls. NOTE2: Shipping was great 2 days or less. One part arrived on a Saturday. P>S> I do not know the age of this mixer. The age drop down menu should have an UNKNOW option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Volant, PA
- Parts Used:
- WP240210-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Teeth broke off pinion gear
I watched the video twice and made the repairs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from Northport, ME
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Worm gear broken.
Followed directions video on line. good directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Spring Valley, CA
- Parts Used:
- WPW10191926
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
37 year old screw cap worn, wouldn't hold bowl with heavy dough
Easy removal of old screw cap, but new one didn't just drop in. Had to scrape paint and a little aluminum to make it fit. Finally did, and it works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Altadena, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Worn out worm (nylon) gear.
Followed up by your précised video, and print copy's which helped me a lot. That's easy!
Was this instruction helpful to you?
Thank you for voting!