3KSM150PSTDR5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dean from Fairfax, VA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer bowl was slipping off the base when in use
Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Lynden, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Thumb screw
the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Albuquerque, NM
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wire Whip was coming apart
Replaced it with a new part. No installation or repair to maching was necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from San Antonio, TX
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pin fell out of neck
Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from South Port, NC
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
mixer stopped working
i followed the instructions in video. Thank you joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bart from Stuarts Draft, VA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worm gear replacement
watched instruction video (from Part Select), the demonstration was close enough to enable me to repair the mixer. Newer mixers are disassembled differently.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from El Paso, TX
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No rotation
I was very happy with the customer services department and the support I received in identifying the part I needed for the repair. I received an email confirming my order with all details. I do wish you had a more cost effective shipping alternative, like Priority mail.
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.
Thank you
Ron Ashby
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.
Thank you
Ron Ashby
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Atlanta, GA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken worm gear
Knob fell out of the front of the mixer into the bowl and jammed the beater. This caused the motor to strip the plastic worm gear. Open unit to investigate and found about 4 teeth missing out of the worm gear. Ordered a replacement. Installed the new gear once received in about 30 minutes. Wife is now happy again. Just need to make sure you pack enough gease into the new gear before reassembling the unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Ledyard, CT
- Parts Used:
- WP243368
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn spring would not allow atthing mixer attacments
Repair was easy. Remove the seal ring with a flat blade screwdriver and drive out retaining pin. Pry out lower unit using two screwdrivers, one on each side. Once apart, use spring clip pliers to remove snap ring. Pull out shaft and replace. Clean and lubricate as you reassemble in reverse. Google the model number to get detailed instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Altadena, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Worn out worm (nylon) gear.
Followed up by your précised video, and print copy's which helped me a lot. That's easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Glen Ellyn, IL
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The screw cap no longer held the bowl in place.
This is the easiest repair ever! I removed the 3 screws, cleaned around the area with a sponge and kitchen cleaner and put on the new cap. The screws went back in easily and voila ! Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marjorie from juda, WI
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
head of screw was broken in half
I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from LIGNITE, ND
- Parts Used:
- WP9709194, WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Beater was peeling and chipped; thumb screw was worn & loose to the point it would fall out
It only involves reinserting the beater . And the thumb-screw was falling out so I cleaned the area and replaced the thumb screw. Very simple and easily done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Holland, MI
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part worn out, wouldn't hold mixing bowl
unscrewed old part, put in new part.New part much better design than old one. Works great. Your service is great. Had the part in a 2-3 days. Awesome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Blairsville, GA
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bent wires in a wire whip
I ordered a new wire whip and attached it just like it was the original. WALLA!!! Done.
Was this instruction helpful to you?
Thank you for voting!