3KSM150PSTER5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced main gears
1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from LIGNITE, ND
- Parts Used:
- WP9709194, WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Beater was peeling and chipped; thumb screw was worn & loose to the point it would fall out
It only involves reinserting the beater . And the thumb-screw was falling out so I cleaned the area and replaced the thumb screw. Very simple and easily done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Holland, MI
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part worn out, wouldn't hold mixing bowl
unscrewed old part, put in new part.New part much better design than old one. Works great. Your service is great. Had the part in a 2-3 days. Awesome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Atlanta, GA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken worm gear
Knob fell out of the front of the mixer into the bowl and jammed the beater. This caused the motor to strip the plastic worm gear. Open unit to investigate and found about 4 teeth missing out of the worm gear. Ordered a replacement. Installed the new gear once received in about 30 minutes. Wife is now happy again. Just need to make sure you pack enough gease into the new gear before reassembling the unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Norfolk, VA
- Parts Used:
- WPW10119326
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
mixer would not turn on
removed one screw from back cover, loosened two screws holding speed control plate, removed one wire at a time from old unit to new, screwed two top screws back on mixer,plug mixer back in, adjust speed control screws until I reached correct speed, put back cover back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Volant, PA
- Parts Used:
- WP240210-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Teeth broke off pinion gear
I watched the video twice and made the repairs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Briggsdale, CO
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worm gear had broken tooth and gear was loose on sprocket
I dismantled the machine to find the problem and to see what part I needed. Than when I ordered the part I saw the video of how to do it. If I had seen the video before I dismantled, I would have save a few steps. The video was very complete and accurate even it being an older model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PJ from Rome, GA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Part to KitchenAid Mixer
Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvaro from Brighton, CO
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worm gear was bad
Order part through parts select. it only took 3 days to receive part. The mixer was very easy to take apart and to replace the gear. it was back together in about 20 min. The video from kitchen aid to repair the unit is awsome. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jennie from cupertino, CA
- Parts Used:
- WPW10674618
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost dough hook so no repair
Just put it on and my challah was perfect!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Saint Joseph, IL
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Coating on original flat beater was cracking.
I just replaced my old flat beater with the new one. It fit and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Salem, IL
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The thumb screw plastic came off
Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Manheim, PA
- Parts Used:
- WP9709707
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Lost a rubber foot on my Kitchen Aid mixer. The remaining feet we're hard and mushroomed. I decided to replace all 5. That was the correct decision.
I griped each foot with a pliers and twisted it out of its setting. I then set a new foot in place and hammered it into place with a small hammer. The feet fit snugly and did not need to be glued. Job was easy and mixer sits like new. I was glad I spent the money to replace all of the feet at once.
Was this instruction helpful to you?
Thank you for voting!