KT2651XWW3 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
attachment planetary gears stripped
removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.
Reassembled mixer.
Was this instruction helpful to you?
Thank you for voting!
Planetary Pinion Gear Assembly had dropped down
The repair was easy, I only had to order new gear assembly parts and to replace the associated worn parts (shaft, pin, and gears).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madeleine from NEW YORK, NY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from SOUTH ELGIN, IL
- Parts Used:
- W11192795
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken gears
Fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LILBURN, GA
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad speed control
Thank goodness for YouTube. Pretty much followed the process of taking it out. Was easy, but having a video made it a bit simpler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EBEN from WEST PALM BCH, FL
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
unit would only operate at high speed
using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCISCO from SAN BENITO, TX
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
REPLACE SPEED CONTROL SWITCH
REPLACE SPPED CONTROL SWITCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from CASTLE ROCK, CO
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Speed control would go from a "mix" setting 1 to a whip setting "10" by itself.
When I ordered a replacement assembly, I was sent a "new" replacement. As I had read up on your site to number the 5 wires BEFORE I removed them, this was a great idea. The new assembly was wired differently than the original board. Although no install instructions came with the new part, it was just a matter of connecting the NUMBERED wires to the new configuration. The first time I fired it up after plugging everything in, nothing happened! I removed all the plug-in wires and reinstalled to ensure I had not gotten a tight connection because of the plastic covers over the end connectors. On my second try, everything worked as advertised! VIOLA!!!! It was a bit tough because of the tight spaces within the motor housing and the new wire routing. Just take pictures of the area BEFORE you disconnect anything and you should do o.k., since I did. 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from GREEN BAY, WI
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Mixer speed control was not connecting properly.
Found a kitchen aid repair video. Found your site for the part I needed. The connections were not like what the video showed but there were enough connector symbols that I was able to understand where they needed to connect. Marking the connections helped for making the new connections when the new circuit board came.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Harrodsburg, KY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Speed switch bad and Initially thought new part was wrong!
At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Pittsford, NY
- Parts Used:
- W11086780
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Gear Stripped was trying to replace
Could not get it properly installed. Had to take to a repair center for completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eleanor from Perry, NY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
thank you,
my hasband did the work and i an so happy it is working good for me now,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Orange Park, FL
- Parts Used:
- WP9708649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Mixer Feet startarted to disintergrate and leave marks on counter
Called original Kitchen Aid and advised had been sold and to look for Kitched Aid on web. Found site, went to appliance diagram and obtained part number and ordered. When parts came in just unscrewed and replaced new feet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lane from Warrior, AL
- Parts Used:
- WP9707223
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
The mixer started getting weak like a gear was stripped and then quite working all together.
I removed the decorative band that covers the seam by removing 1 screw. I then removed the top portion of mixer by removing 4 square head screws. You will then see the gear housing in the front of the mixer. Remove the 4 screws holding that on. There are no spring that are going to pop out and you never know where they went, but be careful because there is a lot of grease and a gear that it just laying in there on the right side. You will see the stainless shaft with a couple on gear cogs on it. Remove the retaing spring from the shaft and pull the top gear off, it may be a little snug. You will then see the dowel pin, mine was sheared off but I could see where it was. Be sure to remove the broken pieces. Use the punch to knock out the remaining pin. Replace with new pin making sure it is evenly exposed on both side of the shaft. Replace the top gear, then the retaining spring, the the gear housing cover, then the mixer top cover and finally the decorative band. Be sure to unplug before you start. These mixers are expensive and expensive to have someone fix them. I ordered 2 pins because shipping is a little high and the pin is cheap. I fixed this for $17.00 total and have a spare pin.
Was this instruction helpful to you?
Thank you for voting!