9KSM150PSPK0 KitchenAid Mixer - Instructions

Looked at the mixer schematic form your website,which made it easy for me to take it apart. Once it was apart & all the grease removed I disassembled & cleaned all the drive parts. Saw what was warn, ordered the parts from you. Three days later received the parts, everything fit perfect. Added grease,assembled the mixer and it ran perfect, good for another 20 yrs. Thank you for making it so easy to repair an old mixer in just over two hours. Rolf

Pulled off end cover. Used the how-to video's to show me how to remove the (3) components (watch out when it comes to removing the spring). Removed all (3) components (one issue was the black cardboard seal, which because of its age broke. Hindsight tells me that I should have purchased a replacement seal along with the (3) new parts.
Fixed the broken part of the seal with scotch tape). Installed all new parts with the help of the video's and put the cover back on. Even with the new parts, the mixer would not run. Come to find out, after I took it to an appliance repair person, that someone had pulled both brushes and put them back in improperly. I could not find a how-to video that showed me how to de-install/re-install the brushes properly. I assume that was because new brushes were no longer available for purchase. At any rate, when the brushes were put in properly, everything worked. The repair person also adjusted the (2) screws on the speed control plate so that when you change the speeds via the lever, it all works properly. I didn't find a how-to video covering those adjustments either.

Repairing/replacing worm-gear (FSP part# W10112253) for a KitchenAid Stand Mixer model number K5SS. First: I am writing this story because all the videos or repair articles I’ve viewed are either misleading or incorrect in that they do not include older K5SS models. 1. These older models from the mid 1960’s or even earlier have four very large #4 chrome plated Phillips Head Screws holding the mixer base to the motor assembly and NOT four small machine screws (one with a lock-washer) as seen on other repair videos. In addition, the stand is composed of two separate pieces with the bottom half being held together with another four identical #4 chrome plated Phillips Head Screws. The upper four holding the stand to the motor housing (I used a manual impact driver to loosen the very stubborn, #4 Phillips screws) must be removed so as to access the four smaller Phillips machine screws (no lock-washers found here, best buy at least four #10, split, before reassembly) 2. Lastly, you will need two pin punches however the recommended smaller 3/32 inch is still too large to remove the pin in the tower assembly. You will need one size smaller or a #4 pin punch instead. These older Kitchen Aid mixers were built with very tight tolerances. Please be patient and take your time removing the pins. Good Luck……. Jim

Got the right parts, very quick delivery, will use again.

I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok

Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.

1. Removed the mixer back plate Cover. 2. Removed the Speed Control Plate and retained spring, wires and ground wire. 3. Removed the old Speed Control Plate screws. Noted Control Plate pitted contact. 4. Removed old Triac Phase Control Board. 5. Removed old Governor. 6. Installed new Governor. 7. Installed new Phase Control Board. 8. Installed new Speed Control Plate and retaining spring. 9. Reattached Speed Control Plate wires. 10. Adjusted Speed Control Plate Screws and set mixer speeds from Stir to maximum settings. 11. Replaced Motor Brushes on left and right side of mixer. 12. Reinstalled mixer back plate cover.

Order the worm gear part number PS11748374.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk

I would recommend two people if possible.

i disassembled the mixer until i could remove the worm gear; is in a housing that that includes another gear and shaft. make sure you have a magnetic tray to put parts in as you work or you will spend more time looking for parts than reassembling the mixer. once you have the gear housing out you will need a small diameter punch to drive out the pin that holds the gears in the housing(i used a 5/32 transfer punch.) make sure you punch the pin out where it will be caught or you will need to order that part because you will not find it. after knocking the pin out it is just a matter of removing the old gear, putting the new one in, and reversing the steps and getting everything reassembled.

Follow a YouTube video step by step

Used the diagram on the website and a video
Totally worked!

Skewer the screw in with my fingers,

Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.

Just put on the new whip...exactly like old one.

I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plugged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!