KP26M1XBS4 KitchenAid Mixer - Instructions

Watched a repair video on the internet. This was actually an easy repair to make. Just make sure you replace all the food grade grease in the gear housing and coat all parts well.

First of all, go to the web site and download the schematics of the model #. It will show all the parts and part #s. Secondly watch a u tube video of the actual strip down process of the professional 600 series stand mixer. With this knowledge, do one of two processes 1: strip down the machine, remove the gears and check for defects- order parts. Or 2: replace all the parts( little money) and have a totally refurbished , smooth running mixer. I kept the good used gears for spares. I replaced 90 % of the internals ( including motor) and have a smooth running machine. I initially burned out the mother 2 months after initial purchase, sent it back under warentee, and received it back . Wen I stripped it down 10 years later, there was very little grease in the gear housing. This is what probable ruined the gears. Use plenty of grease in the housing and gears. The grease is one of the most expensive items, but you can't find it anywhere, so order it, along with everything else, from Parts Select.

Removed top cover, remove snap-ring on shaft, slide top gear and worm gear off. Clean all the grease out and clean parts. Installed new worm gear and parts. Repacked with new grease, careful not to much, leaving room for expansion.

Worm gear strips usually after the lower gear housing breaks. Tore down cleaned grease and shrapnel out, replace stripped worm gear and lower housing. It's convenient that the lower housing plate comes assembled with new bushing and gear. This is now the third one of these expensive mixers I have repaired, word got out that I fix them, and this is a very common problem. Repairs have been for friends and Church, so I don't charge any labor, it's kind of fun, messy, but fun. Note to Kitchen Aid: Please strengthen lower gear case.

removed the cover, separated the gear casing, cleaned the gears, replaced the thrust bearing kit and worm gear, greased all and reassembled. Wish I would have known to order the grease, it would have saved a couple bucks in shipping.

After trying to make a batch of heavy frosting, my KitchenAid mixer final stopped turning. After watching a video of how to change the grease in a similar model on PartsSelect and seeing it wasn't that hard to take apart, I decided to give it a try myself. Removing the cover exposed a completely worn gear drive. Luckily, it was easy to determine which parts needed replacing and PartSelect sent them in no time. Once I put everything back together, it sounded terrible which was pretty tough to take. As it turned out, the problem was flecks of metal from the gear were still in the grease and were getting caught in the mechanism. Once I thoroughly cleaned all the grease out and gave it some fresh grease the machine worked great. Much better than before. I only wish I had swapped the grease out at the same time. Thank you PartsSelect for saving me hundreds of dollars on a new machine!

Removed the cover. Removed the gear assembly cover.. Extracted the C clip with a tool. Removed the bevel gear. Pushed out the dowel pin. Used rubber mallet to push the shaft off the worm gear. Replaced the washer and the worm gear. Used a 1/2" diameter PVC, 3" long over the shaft and on the gear to push back the shaft through the gear with rubber mallet. Pushed back the dowel pin. Reinstalled the C clip. Replaced broken hub bevel gear. Added more grease. Placed the gear cover with 4 screws just tight enough to hold the cover but still allows movement. Turned the mixer to the lowest speed. Allow the cover to self adjust so that the gears have the smoothest sound. Tightened the screws while while maintaining the smooth sound. Turned off the power. Replaced the cover.

Used the meat grinder attachment, with the retaining ring too tight for the motor to turn the augur, so a gear stripped and the mixer would not run. I opened the mixer top, removed the transmission cover, removed enough grease to diagnose the problem (6 teeth stripped off the steel worm gear). I ordered a replacement steel worm gear and, while I was at it, a new retaining ring, bevel gear, retaining pin and the large planetary gear, as I could not tell the condition of these until I disassembled the whole gear train. I then removed the gear train components (needed a snap ring pliers to remove the retaining ring -- I don't recommend trying to remove it with an y other tool), washed them in acetone, cleaned out the transmission case and went over it with a magnet to get stray gear tooth remnants, replaced the worm and bevel gears and reassembled, using the original planetary gear, retaining pin and retaining ring. Filled the bottom of the transmission with planetary grease first, then, once the gear train had been replaced, slathered a big pile of grease over it, replaced the transmission cover. The machine then ran perfectly, so I replaced the mixer's top cover and decorative band and was back in business mixing with it about 30 minutes after cleaning the last of the grease off my hands. I should mention, I used a LOT of paper towels for this job. This was a fun job and I was sorry that it was so easy to do, as I enjoy working with gears and grease.

took off the strap band around mixer, took off the cover (4 screws, took off gear cover (4 screws) took off the retaining ring(used pliers and screwdriver) took off upper gear, took out retaining pin, took off lower gear (becareful to grab the planetary assembly as it will fall out after you take out the retaining pin) cleaned out all of the gear grease (the teeth that were missing were in it. replaced the planetary assembly, lower gear and retaining pin. replaced the upper gear, replaced the retaining ring (used screwdriver and hammer. you have to spread the ring with end of screw driver so it will fit on the shaft then tap lightly with screwdriver and hammer to get it down to the keyway for the ring.) replaced the gear grease with NEW grease, reaplaced the gear cover, replaced the mixer cover, replaced the strap band and plugged it in to test it. IT was quieter than before and works great. i spent less than $30 to repair my 10 year old, out of warranty, Kitchen Aid Mixer. much better than the $32.00 to ship it to factory repair shop and get an estimate to repair. I needed it to make a cake for my nephews wedding. I had my parts in 2 DAYS!!! it was a great experience over all.

I replaced the switch component twice and I still have the same problem. I will purchase a new motor now see if that works? I'll post what happens thanks

The rear 'loop' on the bowl assembly broke off when our cleaning lady tried to wrench the bowl lift handle in the wrong direction. The loop connects to the handle with a rod and spring and the bowl lift mechanism is the piece that slides up and down. I tried to weld the loop back to the bowl lift, but because it is aluminum, it didn't work very well. I purchased the new bowl lift assembly with a new spring (thought I'd lost the first one). This came just as if from the factory, slid it on the track, inserted the rod and screw into the loop and tightened the fastening nut. Easy peasy. Saved myself a $300 - $400 new kitchen aid professional mixer. It did take about 1.5 - 2 weeks to arrive, but it did and that's what counts. Very pleased with my experience.

The transmission housing was cracked and one of the bearings was broken. I replaced both of them, but the mixer really didn't sound any better. So I replaced the gears in the transmission, and while that was better it still wasn't correct. I am going to replace the other bearing and the planetary shaft and see it that aligns everything a bit better. I believe the problem is the way the gear on the end of the motor shaft is working with the worm gear, the bearings are not keeping the correct spacing. Hopefully, the new one in the rear will fix the problem.

I had previously ordered several other gears after I found one of the worm gears stripped. After putting it all back together, the one major gear in the unit that I had not replaced because it looked fine, the bevel gear, also stripped. Learning experience: this is a unit worth several hundred dollars, so don't skimp on a $4 part. Once you work on this thing, you might as well spend a few bucks more and replace ALL the gears - even if they look like they are okay. Furthermore, if you only take 15 minutes to do this repair, as some on this site suggest, you are probably not cleaning the old grease carefully enough. Make sure you properly clean out the old grease to remove any metal from stripped gears, and use a good quality grease to re-pack the gear case.

First and foremost, I am not mechanical at all. I typically refer to parts as thing-a-ma-jigs, and whatca-ma-call-its. When it froze up and started to make a loud grinding noise, I guessed it was a gear problem. I decided to try to take it apart, What did I have to lose? If I couldn't figure it out, I would be down a mixer. I was already down one as it was. It was very easy to take apart and I could immediately see what gears needed to be replaced. Parts Select made it very easy to see what parts I needed. And delivery was lightning fast; the next day after it shipped! I found a PDF on line on how to dis-assemble and re-assemble the mixer. I got it together and it mixed for a few minutes and froze again. I took it apart and realized that I didn't have the whatcha-ma-call-it (worm gear) seated properly. Fixed it and put it back together and put it to the test. Working just fine now! Thank you Parts Select for making this very easy!

removed the cover as stated in the e-mail and followed their recommendations on how to do the repair, the hardest part was removing the retainer clip, job went smoothly. thanks