IMH15XVQ6 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from RAIL RD FLAT, CA
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light bulb out
Put s pot under were you take the screw out.If you drop it you can get it easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GLENDALE, CA
- Parts Used:
- W11256462
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not heating up
Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from IRVINE, CA
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Maintenence
I first unplugged the microwave. I then unscrewed the 2 screws from the top grill. I had to be careful because the grill was cracked close to each screw. It was a little tricky to remove the grill. Had to tilt it down as I removed it, and make sure the microwave door was opened as wide as possible. Filters were placed as the old ones, with the metal part up I believe. A little tricky to get one of the filters to fit. Grill was replaced with care so as not to further Crack it. Kind of maneuvered grill back in place, getting right side in place first. I noticed there were several tabs on the grill that needed to be placed inside of the microwave body while reinstalling the grill. Once the grill was in place, the 2 screws were put in to hold the grill in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from LAKEVILLE, MN
- Parts Used:
- WPW10466420
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable would click, pop, and jerk while running.
Unplug the microwave. Removed the glass tray, the roller ring, and plastic piece that sits on the motor shaft from the inside of the microwave. Remove the 12 Phillips head screws from the bottom of microwave, let the bottom hang down on the mounting hooks at the rear of the microwave. Remove the 2 torx screws from the mounting bracket under the microwave lower the turntable motor remove the two leads. Transfer the rubber washer from the old motor to the new and reassemble and test. It took longer to write these instructions than it did to do the job.
Hint: if the microwave is over a stove lay a towel across the stove to catch any screws that may fall.
Good luck and enjoy your fully functional microwave!
Hint: if the microwave is over a stove lay a towel across the stove to catch any screws that may fall.
Good luck and enjoy your fully functional microwave!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WEST NYACK, NY
- Parts Used:
- WPW10466420, W10337248
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable Motor burned out
Unplug microwave
Remove bottom of Microwave with phillips screwdriver.
Remove connecting wires to Motor
Remove Motor (2 Screws) with Torx Wrench.
Transfer seal from old motor to new moter
Re-install motor
Connect wires
Reinstall Bottom of microwave
Plug back into outlet
r
Remove bottom of Microwave with phillips screwdriver.
Remove connecting wires to Motor
Remove Motor (2 Screws) with Torx Wrench.
Transfer seal from old motor to new moter
Re-install motor
Connect wires
Reinstall Bottom of microwave
Plug back into outlet
r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from MOUNT ULLA, NC
- Parts Used:
- W10269458
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The close door warning kept coming on and the microwave would not run
Don't waste your time with other parts stores online. Partselect sells quality parts and they arrived 2 days early. I purchase a door switch from another online store and the switch was defective.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tanya from LAS VEGAS, NV
- Parts Used:
- W10337248
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sparks from drive coupling
remove 6 lower screws, removed lower panel,2 screws holding drive motor,lower motor, remove old coupling from inside microwave and replace with new coupling, re install motor,install lower panel and screws.no more sparks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kat from Hudson, NC
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights bulbs burned out
Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from MAYS LANDING, NJ
- Parts Used:
- W11025649
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
needed microwave mounting bracket
mounted bracket, case closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAN from CARPENTERSVLE, IL
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
light bulb burnt out .
Turn off power supply at breaker . Replace old bulb with new bulb .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Meghan from WEST JORDAN, UT
- Parts Used:
- W11367904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I accidentally broke the cook tray.
I ordered a new one then put the new one in the microwave. Easiest fix ever!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Hudson, MI
- Parts Used:
- WPW10156813, WP8206419
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Top support for door switch broke.
Part of the support was missing. I had to remove the two switches and put them in the new bracket
Had the switches reversed and started blowing fuses. Reversed them and changed the fuse and it started working.
Had the switches reversed and started blowing fuses. Reversed them and changed the fuse and it started working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MERIDIAN, ID
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Range light bulbs were burned out
We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pablo from Burlingame, CA
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb burned-out
screwed in new bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Cincinnati, OH
- Parts Used:
- W11252182
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turntable broke in half, ring turn needed replaced
I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next
Service was fantastic, parts were ordered one day and received the next
Was this instruction helpful to you?
Thank you for voting!