UMV1160CS0 Whirlpool Microwave - Instructions

I looked up a YouTube video of someone with a similar over the oven microwave. That helped me get into the area behind the control panel where the door switches are. I checked the springs and the cam rocker? The thing that actually hits the button on the switch when the door closes. They were in good condition so I assumed the door switch was bad. There are two so I just purchased one figuring (hoping) that only one was bad. And lo and behold only one was bad. Bing bam boom. Put it all back together and I'm set. Not too difficult. Took a week of work because it takes like 50 days to ship. My kitchen looked like a hurricane after image because of all the parts scattered everywhere.

Whirlpool Microwave was purchased as used item, so installation in a new location required purchase of mounting template, wall bracket, mounting hardware. Granite backsplash cut out using wet/dry diamond blade and Ryobi 6.5 inch saw. Microwave exhaust fan removed and rotated for upward exhaust using modified exhaust plenum from existing stove exhaust hood. Installation of Microwave was the simplest part of the job. All mounting materials worked as required. A list of the materials provided in the hardware mount kit would be helpful, I would not have had to order the top mount screws separately if it was clear that they were included in the kit. Otherwise, no complaints.

Simply need a Phillips head screwdriver, remove the screen covering the light bulb. all you need to do is unscrew burned out bulb and screw in the new bulb. Much easier to order the bulb in the socket and pull it out the socket and plug in the new socket and bulb. because you have a limited space to work

Got some info from the PartsSelect web site and a short YouTube video about how to replace the socket. (Even at 74 years old I'll be darned if I'll pay for a service call if I think I can do the repair myself). Unfastened all the panel screws, swung down the rear-hinged lower panel carefully, then took a couple of pictures showing which wires went to which side of the light socket -- and to the underside of the turntable because those pulled off by themselves when I lowered the panel). Pried off all the silicone sealer around the socket using my fingers, got the old socket out and replaced it, put the wires back in place, refastened the drop-down panel. It was a very easy, straight-forward task that would have taken <15 minutes were it not for the fact that my old eyes had trouble seeing all the screws, even with a flashlight. Everything works fine now.

Remove top grill assembly and replaced filters,parts were delivered on time and fit as expected, Job well done!

Instead of telling you, i have question do you have any instructions on how to do the repair. It would have helped save time on the repair.

This job took longer then it should have, becasue I did not start right in the begining. I did figure it out quickly after the wrong start.

You were a big help in picking the right part to correct the problem. You should be able to help with the repair. Thank You

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using firmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

I unscrewed the bottom plate of microwave oven and took a picture of how the wiring was plugged in and unscrew the motor and put the new one in,it was so easy to do

Followed instruction already on your website

Put s pot under were you take the screw out.If you drop it you can get it easy

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

Removed the microwave from above the oven by loosening the two screws above the microwave. As the unit tilted outward lifted up and the whole unit came out all the time feeding the power cord through the cutout for the power cord. After it was out removed the cover and identified the capacitor and made sure it was discharged and removed and replaced the diode. tested before reinstalling and it heated up just fine. Reversed order and reinstalled . Very easy job maybe a second hand to help fish the power cord when installing and removing.

RATHER EASY. PHILIPS SCREWDRIVER, TORX DRIVER (FOR THE 2 SCREWS SECURING THE GEARMOTOR ITSELF), VERY SMALL SCREWDRIVER TO ASSIST IN DEPRESSING THE DETENTS ON ELECTRICAL CONNECTORS AT THE MOTOR. IF THE MICROWAVE IS ABOVE A STOVE UNIT, IT'S A GOOD IDEA TO PLACE A TOWEL DOWN ON THE STOVETOP TO CATCH ANY WAYWARD SCREW IF ONE HAPPENS TO GET AWAY. (VOICE OF EXPERIENCE)

Don't waste your time with other parts stores online. Partselect sells quality parts and they arrived 2 days early. I purchase a door switch from another online store and the switch was defective.

Replaced both filters