WMH73521CB0 Whirlpool Microwave - Instructions

I used the microwave model number to order a replacement turntable. We received the item and it did not fit. Not even close. I will have to send it back. Very disappointed

Put s pot under were you take the screw out.If you drop it you can get it easy

Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.

Very easy repair because I had no parts for the job. I did not do the repair because PartsSelect keeps sending me the wrong parts and they do not have a human available to solve my problem. To make matters worse they will not refund my money.

I first unplugged the microwave. I then unscrewed the 2 screws from the top grill. I had to be careful because the grill was cracked close to each screw. It was a little tricky to remove the grill. Had to tilt it down as I removed it, and make sure the microwave door was opened as wide as possible. Filters were placed as the old ones, with the metal part up I believe. A little tricky to get one of the filters to fit. Grill was replaced with care so as not to further Crack it. Kind of maneuvered grill back in place, getting right side in place first. I noticed there were several tabs on the grill that needed to be placed inside of the microwave body while reinstalling the grill. Once the grill was in place, the 2 screws were put in to hold the grill in place.

Unplug the microwave. Removed the glass tray, the roller ring, and plastic piece that sits on the motor shaft from the inside of the microwave. Remove the 12 Phillips head screws from the bottom of microwave, let the bottom hang down on the mounting hooks at the rear of the microwave. Remove the 2 torx screws from the mounting bracket under the microwave lower the turntable motor remove the two leads. Transfer the rubber washer from the old motor to the new and reassemble and test. It took longer to write these instructions than it did to do the job.

Hint: if the microwave is over a stove lay a towel across the stove to catch any screws that may fall.

Good luck and enjoy your fully functional microwave!

Unplug microwave
Remove bottom of Microwave with phillips screwdriver.
Remove connecting wires to Motor
Remove Motor (2 Screws) with Torx Wrench.
Transfer seal from old motor to new moter
Re-install motor
Connect wires
Reinstall Bottom of microwave
Plug back into outlet

r

Don't waste your time with other parts stores online. Partselect sells quality parts and they arrived 2 days early. I purchase a door switch from another online store and the switch was defective.

Removal of Phillip Head screws from Top vent and Control panel. Removed Torx head screw to remove entire switch assembly. Removed three wires to switch leads. Unclipped old switch. Replaced wires and inserted New switch in to clips. Attached assembly with Torx screw. Set Control panel back into place and screwed in top screw. Replaced upper vent with 2 screws.

remove 6 lower screws, removed lower panel,2 screws holding drive motor,lower motor, remove old coupling from inside microwave and replace with new coupling, re install motor,install lower panel and screws.no more sparks

Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.

mounted bracket, case closed.

Turn off power supply at breaker . Replace old bulb with new bulb .

Part of the support was missing. I had to remove the two switches and put them in the new bracket
Had the switches reversed and started blowing fuses. Reversed them and changed the fuse and it started working.

We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.