MH2155XPQ1 Whirlpool Microwave - Instructions

Removed screws holding the broken grill tabs with a phillips screwdriver
Removed broken grill and all broken tabs that fell into the vent area
Cleaned area where the new grill was to be placed
Inserted new grill onto the appropriate tabs and tightened the screws

BE CAREFUL as the tabs on the grill are thin and fragile when you insert the new grill don't force it into the slots, I used a knife as a way to slide the grill into place.

removed the two screws, removed all of the broken tab pieces, replaced with new grill, put the two screws back.,....DONE Easy as pie

After reading other entries, I have determined this is a problem with most grills on the whirlpool microwaves. Defective material ..becomes brittle and crumbles.

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

Searched on the internet for repair assistance and found YouTube video that helped alot.
Need to provide installation directions in the product.

Removed 2 screws from top of microwave. Place new grill in place. Replaced 2 screws that were removed. What was wonderful is I ordered the part around 3 pm on a Friday. The part arrived at 9AM the next day and that was without requesting special shipment.

Unscrewed the remaining pieces of bracket slipped in new vent cover and attached with the two screws. Very easy since the web site showed where the vent attached. I saved over $60.00 doing this repair myself!

Take off top facing over microwave using screwdriver also protection plate for diode and capaitor. Disconnect diode from frame, bracket to capacitor then remove, disconnect wires leaving diode on capacitor for right connection, replace, rewire done.

Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.

I removed the two screws and took off the old grill. Snapped the new grill in place and replaced the screws. This model was not shown on the list but the part fit just fine. The part arrived in 2 days! I ordered the white one and at first didn't think it matched .. maybe my microwave was bisque or almond .. but after 15 minutes of scrubbing I realized it was white but just real dirty .. lol. Now the door opens without the grill falling off. Easy fix.

I didn't have to remove the old cover since it cracked and fell off the microwave already. I simply snapped in the new vent cover, screwed in the 2 screws and I was done. Super easy.

-leave door attached to microwave.

-remove three phillps screws from end of door next to handle.

-use two flathead screw drivers to pry apart the outside cover and unsnap the two sections of the door. Start in the top middle.

-use phillips screw driver to remove two screws holding handle on.

--handle has an up and down side, attach longer side to the top of the door.

-snap two door pieces back together.

repair was very straight forward and can be done by anyone with reasonable mechanical ability. I read in a couple places where appliance repair people had said it was best to replace micro wave unit as it was near impossible to do repair. Pure rubbish; only problem I had was when the door and glass u it arrived the glass wasn't glued in completely and I had to clue it myself. I removed the three screws on the right end of the door and took my large pocket knife and ran it down the joint where the outer cover meets the metal door. first the top and then the bottom and the old door popped right off. removed the old handle from old door for the screws needed to reattach the new handle to new cover. I started the screws on the counter to get threads started in plastic made attaching to cover easier. hen started by pushing the new cover onto the left end of door the continued squeezing the cover on along to the right first top and then the bottom a little at a time and it snapped right in for me with a fair amount of pressure, replaced the three screws and it works great looks like new. I did remove the upper vent to clean and that helped some with installing. Very easy and beat the heck out of trying to replace the entire unit. I think the so called appliance repair people only wanted to sell and install a new one for $$$$.

Removed the microwave from above the oven by loosening the two screws above the microwave. As the unit tilted outward lifted up and the whole unit came out all the time feeding the power cord through the cutout for the power cord. After it was out removed the cover and identified the capacitor and made sure it was discharged and removed and replaced the diode. tested before reinstalling and it heated up just fine. Reversed order and reinstalled . Very easy job maybe a second hand to help fish the power cord when installing and removing.

Put s pot under were you take the screw out.If you drop it you can get it easy

Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.