MH8150XJB1 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT from LEESBURG, FL
- Parts Used:
- 8183852
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
existing vent grill cracked
the new part fit just right. put in place and screwed in with existing screws. like a glove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from FRANKLIN, TN
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave vent cover broke as it was cleaned.
Bought a new one. Perfect match, easy replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from BECKLEY, WV
- Parts Used:
- 8183852
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Exhaust Grill cracked
Simple repair. Remove 6 screws to remove old grill and replace with the new grill using the old screws.
Was this instruction helpful to you?
Thank you for voting!
Very unusual. we had a brief fire inside the microwave which destroyed all the moving rotary parts.
First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple
Was this instruction helpful to you?
Thank you for voting!
The air filters were fine. The Front grill did no or could not fit. It too big however, not bu much, just enough so it will not fit the space. If it could fit the space with enough room to close the door I could screw it in
PRAY !Pray hard
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from HOLLY LK RNCH, TX
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Clips on grill broke
Removed bed two screw replace grill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monty from Mansfield, TX
- Parts Used:
- W10642989
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace turntable motor
removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SAN ANTONIO, TX
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Vent grill replacement
Unscrewed 4 different screws, replaced the vent & returned screws. Ack to original positions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from ORANGE, CA
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael J from LORAIN, OH
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb which lit the surface of the range.
Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from El Dorado Hills, CA
- Parts Used:
- 8183852
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace broken grille vent
PartSelect was the only company to show that the part came in 3 different colors. The grill vent was used to replace a cracked vent. It was simmple to slip in the new vent,but be sure to save the existing screws that holds the vent in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Annapolis, MD
- Parts Used:
- 8183852
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old grill vent's brackets broken off.
Removed retaining screws and broken parts; inserted new grill and screws. Fin!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Smithtown, NY
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
machine was dead.
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mouang from Sacramento, CA
- Parts Used:
- 4393799
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Glass tray shattered
Ordered the glass tray and installed it. Received the orderin about two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Basehor, KS
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
grill mounting braket broke
The part came very quick less than a week. The installation took less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!