MH1150XMS0 Whirlpool Microwave - Instructions

-leave door attached to microwave.

-remove three phillps screws from end of door next to handle.

-use two flathead screw drivers to pry apart the outside cover and unsnap the two sections of the door. Start in the top middle.

-use phillips screw driver to remove two screws holding handle on.

--handle has an up and down side, attach longer side to the top of the door.

-snap two door pieces back together.

repair was very straight forward and can be done by anyone with reasonable mechanical ability. I read in a couple places where appliance repair people had said it was best to replace micro wave unit as it was near impossible to do repair. Pure rubbish; only problem I had was when the door and glass u it arrived the glass wasn't glued in completely and I had to clue it myself. I removed the three screws on the right end of the door and took my large pocket knife and ran it down the joint where the outer cover meets the metal door. first the top and then the bottom and the old door popped right off. removed the old handle from old door for the screws needed to reattach the new handle to new cover. I started the screws on the counter to get threads started in plastic made attaching to cover easier. hen started by pushing the new cover onto the left end of door the continued squeezing the cover on along to the right first top and then the bottom a little at a time and it snapped right in for me with a fair amount of pressure, replaced the three screws and it works great looks like new. I did remove the upper vent to clean and that helped some with installing. Very easy and beat the heck out of trying to replace the entire unit. I think the so called appliance repair people only wanted to sell and install a new one for $$$$.

Used a phillips screwdriver to remove 4 retaining screws located on the top leading edge of the unit, just above the door. Note the screws on the far left and far right are shorter than the middle two. After removing and cleaning the plastic vent, the small, square charcoal filter is revealed in the center, and is easily removed (noting its installation position first!). Take advantage of the opportunity to thoroughly clean the inside using a cloth soaked in degreaser before replacing the filter, the vent, and the 4 screws.

Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.

Removed the old vent grill by removing the two screws and put in the new one.

Very simple, just removed the screws and plates from the top of the microwave and reused the screws to secure the new piece.

Removed the two screws hlolding the old vent in place. Discarded the old vent. Snapped the new vent in place and attached with the two screws previously removed.

Is there an instruction video?

Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.

Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.

Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.

Turned power off. Removed all the screws from bottom removed socket and replaced

easy to replace, just the same as cleaning the turntable and placing back in the micorwave;

screwed in new bulb

Washed the glass tray and put in the microwave oven. Easy..