GT4175SPT1 Whirlpool Microwave - Instructions

The instructions on the website were incredibly easy and I saved myself a lot of headache by using this site.

-it was built in unit - so I needed to pull the decorative grill from around the outside to remove it from the wall
- removing the back of the case involved removing phillips head screws from along the side and back of the unit. the only issue I encountered on removing screws was the fact that the "torx / star" screws could not be fit with the wrench that I had (they had a pin in the center that would not allow the wrench to fit into the star). However, a pair of pliers was handy and they were removed just easily.
- I had ordered both the high voltage diode and magnetron because I didn't know which item was the problem. I grounded the diode with two screwdrivers while wearing rubber gloves to be safe. the warnings on this did the trick as it was the only scary part of the operation.
- the diode was a little hard to spot looking at the schematics, but is is found on the lower right corner of the right side of the panel and easily pulled out and replaced. I tried the microwave again to see if it worked...and it did not. So I confirmed that the magnetron was the issue.
- removing the screws for the magnetron and putting in the replacement was a dead easy and I tried the microwave again before putting cover back on. Worked like a charm. Super easy!

Took microwave out of builtin cabinet with 4 screws.
Put microwave on center island and removed cover.
Tested interlock switch with volt meter and it appeared ok so I put my kit back in box and sent back.
Took out magnetron unit and replace with new part.
Put cover back on and test.
All is working and installed back in cabinet. Two weeks later all still working great.

I took the microwave out of the cabinet compartment and placed it on the counter. I removed the torx screws from the back and the two phillips head screws from each side. I then pulled the cover back and off. I removed the broken latch piece by pushing it away from me until the outside nipple was free and then pulled the piece out. I opened the door by pushing up on the latch with a flat head screwdriver. I put the end of the new part into the area behind the latch and on top of the microswitch and pushed until the outside nipple would slide into the slot. I then replaced the cover and secured with the screws taken out initially. Done.

The power on the microwave went completely out when I went to use it, but there was no power failure for the house or neighborhood. We removed the microwave from above the oven. Took out the screws on the sides and back of the microwave and slid the top back. The line fuse was located on top unobstructed, NOT behind the button panel like some microwave models. As the appliance is over 20 years old the line fuse was quite old. It was really hard to pry it out of its holder and actually broke. I used a vacuum to suck up the dust and glass and it was easier to get out the ends once the middle broke. Popped the new line fuse in, slid the top back on, put in the screws and put the microwave back in its compartment above the stove. Good as new!! We were about to spend money on a new microwave, but thankfully I came across this site. So happy I did!!

This repair was really easy. The part that took the most time was taking it down from it's compartment above the oven and putting it back up there once repaired.

The push button door latch had broken on my microwave. After digging into the unit-which was the hardest part, getting the shell off and getting at the control panel, I was able to see an interior latch part that had one side of plastic broken off. 40. repair piece later and I was able to plug that in, put it all back together and it works, although it does not feel that solid or that it will last a lifetime. Glad I was able to fix instead of calling a repair guy.

Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos

The lack of magnetron operation was immediately diagnosed as a door switch problem. This as a cheap and quick repair, simply removing some of the cover screws (some of which are security-style Torx) on the back and right side of unit. It is not necessary to remove the cover completely, just to gain enough access to swap the micro-switch in. The microswitch itself is retained by plastic tabs, and a plastic dowel. The wires are spade connectors that are very tight, and may require needle-nose pliers to manipulate. The enabled the oscillation circuit (magnetron) to engage.

However, the turntable still did not turn when the magnetron was activated. Removing the turntable and support assembly, the turntable support was damaged at the coupling socket to the motor. A small straw was affixed over the motor to ensure it was still spinning, but it was found to have failed, as well. A new turntable support and motor were ordered and installed. It required completely removing the top and bottom covers. Be careful not to remove the bolts for the transformer, attached to the bottom cover in the right side with different style bolts than the standard cover screws. This will allow the transformer to move, and as it is very heavy, it can damage wiring or other sensitive parts. Once the bottom cover is removed, the motor is easily and quickly removed by removing one screw and tilting the motor housing around a retaining tab. Assembly is reverse. Aligning all of the the cover tabs simultaneously is the most difficult part of the process.

Remove from cabinetry, take cover off and had a very difficult time removing the plastic form that has the switched in. Replace the lowest of all the switches, and then again very difficult time getting the plastic form back in. Some of the plastic even broke during the process but not any that could prevent it from working as it did before. I had ordered a fuse, 2 packs of 2 switches as there are 3 switches but only had to use 1 to get it working again. Tested after switch install, put the cover back on and reinstalled in the cabinet.

Replaced Door latch Bracket.
Filed a bit off the bracket connection fingers so to fit into the slot.

Removed M/W oven case/cover. Identified part needed. Found part online with in 2 minutes, ordered new door latch actuator, installed with part arrived within two minutes, reattached case/cover, reinstalled M/W.

The tip on the end of the latch broke off, so I had to carefully pry it back in without breaking the new piece. Took a few tries, but got it.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

My wife was pushing a few buttons with her knuckle (hands were full)and the microwave just turned off. Just like we had blown a breaker. First I unpluged it. Then I removed the phillips screws of the front panel, and found and removed the ceramic fuse. 3 days later I received the new fuse in the mail, and put it in. I plugged the microwave back in and it works great.

It literally took me longer to unpackage the fuse than to install it. I removed the outer shell by unscrewing the five screws, lifted it off and set it aside. The old fuse was readily visible so I pulled it out and put the new one in its place. I set the shell back on and replaced the screws. I plugged it in and ran it for 30 seconds while still in the shop just to make sure that solved the problem and presto - it worked like a charm. A $20 part saved me from having to purchase a new microwave (sadly, I had to break the news to the wife).

1. Remove the trim frame off of the front of the cabinet (4 Phillips screws). At this point, take glass plate and turntable frame out of unit. 2. Slightly lift the unit off the cabinet frame (which is attached to the cabinet) so the feet on the microwave allow the unit to clear the frame and then remove microwave from the cabinet. 3. Once slightly removed from the cabinet, unplug the unit before completely removing it from cabinet. 4. Take 2 Phillips screws out of the side panels. 5. Take about 6-7 T20 Star Pin screws out of the back of the panel. (This may require you to purchase this special tip if you don't have it in your toolbox). 6. Slide the microwave cabinet toward the rear of the unit (the front portion clips into the frame ... don't try prying it off because you'll damage the unit). 7. Completely remove the microwave cabinet housing. 8. Be careful not to damage or catch any internal wiring inside the unit while the cover is off. 9. Turn unit on it's back and remove 4-5 Phillips screws holding the bottom cover in place. Remove bottom cover. 10. Now notice that the turntable motor is completely exposed. 11. Remove the wiring harness from the motor (notice which connection clip has the black wire). 12. Remove the one Phillips screw holding the motor to the frame. 13. Clean around the area in case food spills may have gotten into the area. 14. Insert new motor, put Phillips screw back in and attach power connection. 15. From this point on, just reverse steps to re-assemble microwave and put back in cabinet. 16. Test new turntable motor. 17. Enjoy the smile from your wife because she can now use the microwave!