GH9185XLB0 Whirlpool Microwave - Instructions

I ordered the part according to the Model number, inserted the part very easily, (and I am soooo challenged in that area) and now it turns again. :)

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using firmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

replace one of the four rack supports which was melting

I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the microwave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!

the burn thru was probably because stirrer motor was not turning, Unplug the microwave .freed the motor up bu manually turning. temporary fix. The cover is held up with small push pin clips. Just pry the cover off with a screw driver or other flat tool. Scrape offf the old silicone. There are two covers in the Kit. you just need 1. Remove the old clips for the roof of the microwave, put a bead of silicone on the new cover where the old was and secure the new cover with the push pins into the clips .

Put s pot under were you take the screw out.If you drop it you can get it easy

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

Remove the microwave from its mount above the stove. Remove the sheet metal top/sides piece. Pop the control panel loose to allow access from the front. Remove more screws that will allow the small inverter to be removed and the big inverter housing to be wrangled loose enough to remove the big inverter. Pop the inverter cooling fan from its mount. Disconnect wires and remove screws to remove big inverter. Install new inverter in reverse process.

Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.

Simply remove two screws with a crosstip screwdriver securing the vent louvers from top of microwave, remove the old charcoal filter and replace new filter as describe in the owners manual. Very easy installation and partselect parts are very inexpensive and durable to other sites.

Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.

We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.

Washed the glass tray and put in the microwave oven. Easy..

Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.

I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next