MH1150XMS3 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Myrtle Beach, SC
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Vent Grill was broken
I slid the new grill into position and secured it with the original two screws. Could not have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Shelley, ID
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old vent grill broken
Removed to screws from oven to grill. removed grill. put in new grill and replaced the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Baltimore, MD
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass turntable
No repair- just replaced glass turntable.
Right part I needed with first try
Right part I needed with first try
Was this instruction helpful to you?
Thank you for voting!
son bought home with microwave with missing parts
glass tray and support ring just went in and the grille just screwed in, and the microwave was like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Millersville, MD
- Parts Used:
- 8206232A
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bult needed to be replaced
The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the light bulb so that we do not need a screwdriver to remove the door to get to the light bulb
Was this instruction helpful to you?
Thank you for voting!
The top front grille screwed in tabs had cracked
The trick is to align the bottom and top tabs first. This take a little coaxing and patience, but once these snap in, the tabs with the threads line up perfectly.
TIP: Thread the screws into the metal tabs while supporting the tabs with your hand BEFORE installing the grille, back them out, and then install. The threads were a little tight, and putting a lot of pressure on them while the tabs are in the slots risks breaking them off.
TIP: Thread the screws into the metal tabs while supporting the tabs with your hand BEFORE installing the grille, back them out, and then install. The threads were a little tight, and putting a lot of pressure on them while the tabs are in the slots risks breaking them off.
Was this instruction helpful to you?
Thank you for voting!
Replace vent grill and filters.
I went online and found the manual for this appliance and used the instructions, which were very helpful. The filters just pop out and the new ones fit right in. No tools were needed. For the vent grill, it was necessary to move the metal tabs back and forth a few times manually before they were properly placed in order to take the two screws, which hold the grill in place. I then loosely tightened the screws (so as not to crack the plastic grill)with a Phillips Head screwdriver. When my husband got up from his nap he was pleased to see the job completed without his help.:)
Was this instruction helpful to you?
Thank you for voting!
no heat
this problem started two months ago when my micro quit heating up, after all the research most agreed it was the magnetron. taking the micowave apart is not to difficult just make sure you bag all the screws accordingly. the high voltage area is on the right hand side behind a panel. caution there is a capacitor that will bite if your not careful, need to short the circuit between the two connectors with an insulated screw driver it will make a small pop or let it sit for awhile and it will discharge by itself. The magnetron worked for two days then quit, after more research i took it apart again and tightened up all the connections. Worked great on the bench but when i got it back up on the cabinet two dayslater kaput again. so again i take it down and replaced the two cheapest parts in the high voltage system, magnetron thermst fix, and h.v diode. benched tested it this time for 3 days cooking anything that i could think of, worked great. its been one week now afer installtion and it is still working.
Was this instruction helpful to you?
Thank you for voting!
Replaced vent grill and grease filters
The repair was simple and easy. It required a Phillips head screw driver only. I Removed the vent grill and replaced it with the new grill there were only two screws that needed to be removed then refastened. Total five minutes. I also replaced the grease filters which took about a minute total time. I do many of my own repairs to my home and appliances .I've found your service parts delivery prompt and precise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Edmond, OK
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave vent cover was broken
Repair part delivered only a few days after purchasing on-line. The replacement part was the exact same as that on the original unit. Installation took about 1 minute involving 2 screws. Ordering was very easy.
This is a highly recommended parts store.
This is a highly recommended parts store.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Pembroke, MA
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulb "burnt out"
Removed 1 screw, removed "burnt out" bulb and replaced it with new bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEPHEN from FORT MYERS, FL
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass microwave turntable shattered while taken out for a cleaning.
PartSelect had the turntable I needed at the best price. Ordering was easy, but best of all, the part was delivered next day. I was able to insert the new turntable plate into the microwave and it was good as new.
Was this instruction helpful to you?
Thank you for voting!
light bulb burned out
when removing the bulb the base broke off and there was an ark took place as I had made a mistake and didn't unplug the unit before working on it , thought with the light switch off it was ok, but still had power in that area . So ALWAYS uplug before making repairs.
The whole unit was dead and I checked for power at the plug and it was live. after unpluging I took the main control panel off and discovered a fuse was blown and replaced it along with a new socket and bulb and now it works like new . the fuses are inside small plastic capsuals so I back probed them with continuity light to find the blown fuse .
It was quite simple once I found how to get the panels off. Just basic common sence will take care of most appliance problems
thanks
Louie Scholl
The whole unit was dead and I checked for power at the plug and it was live. after unpluging I took the main control panel off and discovered a fuse was blown and replaced it along with a new socket and bulb and now it works like new . the fuses are inside small plastic capsuals so I back probed them with continuity light to find the blown fuse .
It was quite simple once I found how to get the panels off. Just basic common sence will take care of most appliance problems
thanks
Louie Scholl
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Hauppauge, NY
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement turntable glass
Opened the box and popped it in. No problem with that.
Was this instruction helpful to you?
Thank you for voting!