YWMH31017AS0 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Shirley from Londonderry, NH
- Parts Used:
- 8206232A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out light bulb
The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roger from palm coast, FL
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace light blub
removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ethel from New Berlin, WI
- Parts Used:
- 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed a clean filter
Stood on a step stool (microwave over stove), took off the one panel,removed old filter and put in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Cranston, RI
- Parts Used:
- W10208631A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
replace filter
slide into place under hood
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from Mesquite, TX
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb burned out
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Oakland, NJ
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
changed filters
Replaced filter which came inrecord time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Gatlinburg, TN
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb
Replaced light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carter from McCordsville, IN
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burn't out bulb.
Removed the glass cover and replaced the bulb. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from New Berlin, WI
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Clearing the clean code was the hardest part.
I had no problem installing the new filter. Just used a phillips screw driver to remove the two screws holding the vent cover in place. Cleaned the dust out of the ducts and reinstalled the new filter. The screws must be held to the screw driver with your finger tips so you don't drop them in the vent cover. The most difficulty I had was in clearing the clean code from the screen. There are no instructions in the owners manual for doing this. But after several tries I got it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carole from North Canton, OH
- Parts Used:
- 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
in 2 yrs the charcoal filter had NEVER been changed and it was smelling horrible--so had to be done !
--simpley removed 2 screws, removed old filter--but had PLENTY of cleaning to do before putting in the new filter !My husband LOVES to cook and pan fry foods--it won't go that long before being replaced in the future!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from North Olmsted, OH
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Reminder signal and message to change filter on microwave digital display.
Removed 2 screws on the top of the microwave and removed top/front piece of microwave. Slid out old filter (which didn't look dirty at all) and replaced it with the new one. Replaced top/front piece and 2 screws. It took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!